Climax Technology Co Ltd CTC1052RV Manuale Utente

25 

z  If an alarm is successfully reported, 

after the Monitoring Center calls back 
within this 5-minute period, CTC-
1052RV auto-answers the call after 
the 1st -2nd ring and waits for proper 
Access Code (default is 1111) entry 
followed by the (#) key within 15 secs. 
Please enter Access Code in normal 
operation speed. 

z  Upon the correct Access Code 

received, CTC-1052RV will then open 
a Full-Duplex Communication to allow 
the Call Recipient to speak to CTC-
1052RV Pro /WTRV/WTRVS directly. 
You can also use the following DTMF 
command to switch the speech mode. 

„ Enter 

(1) to TALK ONLY  

„ Enter 

(2) to open TWO-WAY VOICE 

COMMUNICATION  

„ Enter 

(3) to LISTEN-IN ONLY 

„ 

End a Call: enter (9) to HANG UP or 
put the handset  back into the base 
cradle. 

„ Enter 

(7) to Speaker Volume Control 

and then press (6) or (4) to increase 
or decrease levels of speaker volume 
in the “Two-Way” communication 
modes.  

„  Enter (8) to Microphone Sensitivity 

Control and then press (6) or (4) to 
increase or decrease levels of 
microphone sensitivity in the “Two-
Way” communication mode.  

„  Press any DTMF key,

 

except the 

designed “hang-up” key (9), to add 
another preset communication time. 
Please note that when a particular 
DTMF key is pressed, its designed 
shortcut function will be executed & 
the communication time will be 
extended at the same time. 

) 

Please note that if you wish to enable a 
designed shortcut function, please press 
DTMF keys over 1 second to enable the 
function you desire.  

) 

If the levels of speaker volume and 
microphone are adjusted in the two-way 
communication between the Control Panel 
and the emergency call recipient, the 
adjusted value will be restored. 

 

) 

If the two way communication is setup 

between WTRV/ WTRVS and the 
emergency call recipient, the levels of 
speaker volume and microphone 
sensitivity can not be adjusted.  

  

If Command #38 is set as 0, Follow-On, or 2, 
Follow-On & Call-Back, it will then follow its 
setting as in Command #45,  Follow-On 
Choice to open Two-way Voice, or, Listen-In, 
or just waiting for commands.  

 

z 

Please note that if an alarm is triggered by 
WTRV or WTRVS, for follow-on operation, no 
matter what Follow-On choice (Command 45) 
you have set, the Monitoring Center personnel 
have to press the DTMF commands as below 
and the Monitoring Center can remotely control 
CTC-1052RV: 

 

 

 

If an alarm is triggered by any compatible 
device (except WTRV/ WTRVS) or pressing 
the Help Button on Panel, the system will 
follow the preset Follow-On Mode (Command 
45) to respond accordingly.The Monitoring 
Center can remotely control CTC-1052RV by 
the DTMF commands as below: 

„ Enter 

(1) to TALK ONLY 

„ Enter (2) to open TWO-WAY VOICE 

COMMUNICATION  

„ Enter 

(3) to LISTEN-IN ONLY 

„ 

End a Call: enter (9) to HANG UP or 
just put the handset  back into the 
base cradle. 

„ Enter 

(7) to Speaker Volume Control 

and then press (6) or (4) to increase 
or decrease the levels of speaker 
volume in the “Two-Way” 
communication mode. 

„  Enter (8) to Microphone Sensitivity 

Control and then press (6) or (4) to 
increase or decrease the levels of 
microphone sensitivity in the “Two-
Way” communication mode.  

„  Press any DTMF key,

 

except the 

designed “hang-up” key (9), to add 
another preset communication time. 
Please note that when a particular 
DTMF key is pressed, its designed