Honeywell International Inc. 8DL5842 Manuale Utente
DRAFT – 24 February 2004
K9674ax 2/04 Rev. A
$'(0&2
:LUHOHVV'LDOHU
Installation and Setup Guide
GENERAL INFORMATION
The 5842 Wireless Dialer is a combination Central Station
dialer and RF transceiver. It receives and acknowledges RF
messages from the control’s transceiver. In response, it
sends reports to the central station via the dialer. The 5842
also sends acknowledgements, supervisory and tamper RF
transmissions to the control.
dialer and RF transceiver. It receives and acknowledges RF
messages from the control’s transceiver. In response, it
sends reports to the central station via the dialer. The 5842
also sends acknowledgements, supervisory and tamper RF
transmissions to the control.
DIALER FEATURES
• ADEMCO Contact ID® central station reporting format.
• Reports low battery conditions to control panel.
• Front cover tamper switch.
The LEDs and their functions are described below:
LED Function
Green
Lights continuously and flickers during RF activity.
Yellow
Flashes once each time the 5842 sends an
acknowledge message to the control. Stays on while
the dialer is using the telephone line.
acknowledge message to the control. Stays on while
the dialer is using the telephone line.
Red
Lights to indicate no setup information has been
received, or setup information is incomplete. Once
setup information is received the LED will go off.
received, or setup information is incomplete. Once
setup information is received the LED will go off.
RED
YEL
GRN
MOUNTING
HOLES
(4)
ANTENNAS
(INSERT IN
RIGHT-HAND
TERMINALS)
BREAKOUT
WIRING
OPENING
WIRING
OPENING
TAMPER
SWITCH
SWITCH
RJ31X
TELEPHONE
JACK
WIRING
OPENING
OPENING
5842-001-V0
TELEPHONE IN
TELEPHONE OUT
RJ11
TELEPHONE
JACK
TELEPHONE
JACK
BATTERY
BATTERY
Figure 1 - 5842 Wireless Dialer (cover removed)
OPERATION
The 5842 dialer is triggered by an RF message that contains a command, (i.e. a dialer report message or a line seize and clear
command). It processes the command and remains active for a short time after it has received and acknowledged the last RF
message from the control panel. The 5842 then reverts to Low current standby mode. The Wireless Dialer is normally in a low
current standby mode, which maximizes battery life. At specific intervals the unit’s RF receiver is switched on, and listens for a
“Time Sync” message from the control panel. If the “Time Sync” message is not received within a specified time the 5842 switches
to an active receiving state. If the 5842 still does not receive a message it transmits a time sync fault to the control panel. Normal
operation resumes after the control panel logs the event and transmits a “Time Sync Fault Restore” message. Failure to receive a
kiss-off signal from the central station is reported to the control panel. Dialer reports are sent to the central station using
ADEMCO Contact ID® format only.
command). It processes the command and remains active for a short time after it has received and acknowledged the last RF
message from the control panel. The 5842 then reverts to Low current standby mode. The Wireless Dialer is normally in a low
current standby mode, which maximizes battery life. At specific intervals the unit’s RF receiver is switched on, and listens for a
“Time Sync” message from the control panel. If the “Time Sync” message is not received within a specified time the 5842 switches
to an active receiving state. If the 5842 still does not receive a message it transmits a time sync fault to the control panel. Normal
operation resumes after the control panel logs the event and transmits a “Time Sync Fault Restore” message. Failure to receive a
kiss-off signal from the central station is reported to the control panel. Dialer reports are sent to the central station using
ADEMCO Contact ID® format only.
PROGRAMMING AND INSTALLING THE 5842 WIRELESS DIALER
Refer to the following procedure and the Installation and Setup Guide for the Control Panel being installed to program and
install the 5842 Wireless Dialer:
install the 5842 Wireless Dialer: