Honeywell International Inc. 8DL5842 Manuale Utente
-2-
If the 5842 batteries are removed refer to REPLACING THE BATTERIES section before reinstalling/replacing the cells. Use only
1.5-volt alkaline batteries. Observe the polarity when installing batteries.
1.5-volt alkaline batteries. Observe the polarity when installing batteries.
STEP DESCRIPTION
1.
Remove the cover from the 5842 Wireless Dialer.
Note: The 5842 is configured to accept programming data any time the cover is removed from the unit. The unit performs this function whether or not it has
been previously programmed.
2.
Place the control in the Programming Mode and enable operation with the 5842 Wireless Dialer. Refer to the procedure in the Installation
and Setup Guide for the Control Panel that is being installed.
and Setup Guide for the Control Panel that is being installed.
3.
Install each antenna in the respective right-hand terminal of the two terminal blocks at the upper edge of the 5842’s circuit board, and tighten
the screws to secure them. (Refer to Figure 1.)
4.
Install two 1.5V AA batteries in the 5842. The 5842 will activate its receiver and begin listening for an RF broadcast from the control panel.
The panel’s Green, Yellow and Red LEDs will come on for one- (1) second after the unit is powered-up.
The panel’s Green, Yellow and Red LEDs will come on for one- (1) second after the unit is powered-up.
Notes:
(1) Do not mount the 5842 or install the cover at this time.
(2) To conserve battery life, the 5842’s listen mode has a five (5) minute time-out. If the 5842 times out, install and remove the cover to restart the
listen mode.
5.
Exit the control panel’s programming mode by entering
✻99.
6.
The control panel will transmit the setup information and the 5842’s Green and Yellow LEDs will flash briefly.
7.
The control panel will indicate receipt of the RF acknowledgement from the 5842 by beeping three times and the 5842’s red LED will go out.
8.
Install the cover on the 5842.
9.
Place the control panel in Go/No Go Test Mode.
10.
After selecting a mounting location for the 5842 remove and replace the cover to activate the tamper and ensure the control has received the
transmission.
transmission.
11.
Exit the controls Go/No Go Test Mode (Refer to the Installation Instructions for the Control Panel being installed) and cause the control to
send several dialer reports via the 5842. Ensure that the central station receives each report.
send several dialer reports via the 5842. Ensure that the central station receives each report.
12.
For concealed wiring, route wires through the rectangular opening at the rear of the base before mounting. For surface wiring entry, a thin
breakaway area is provided along the base's right edge.
breakaway area is provided along the base's right edge.
13.
Mount the case back to a wall or to and electrical box using the 25mm-long self-tapping screws that are supplied (mollies for drywall are not
supplied).
supplied).
14.
Make Phone Line Connections - For local or full line seizure proceed to the appropriate steps below and refer to figure 2.
Local Seizure: Only the telephone equipment connected to the 5842 Wireless Dialer’s RJ11 jack will be disconnected to prevent
interference while the 5842 is using the phone line. This may or may not include ALL the telephone equipment on the premises.
interference while the 5842 is using the phone line. This may or may not include ALL the telephone equipment on the premises.
a. Connect the incoming phone line to the 5842’s internal RJ31 jack.
b. Connect the handset phone lines to either 5842’s internal RJ11 jack.
b. Connect the handset phone lines to either 5842’s internal RJ11 jack.
Full Line Seizure: Requires the installation of an RJ31X jack at the network demarcation (before any other premises connections). It
ensures that the ALL premises telephone equipment is disconnected and will not interfere with the 5842 while it is using the phone line. In
the event of a problem with the 5842 it will also ensure uninterrupted service to all premises telephone equipment when the cable to the
5842 has been disconnected from the RJ31X jack.
ensures that the ALL premises telephone equipment is disconnected and will not interfere with the 5842 while it is using the phone line. In
the event of a problem with the 5842 it will also ensure uninterrupted service to all premises telephone equipment when the cable to the
5842 has been disconnected from the RJ31X jack.
a. Cut the incoming RING and TIP phone lines (typically red and green, respectively) and connect them to RJ31X terminals 4 (red) and 5
(green).
b. Connect the premises end of the cut RING and TIP wires to RJ31X terminals 1 (grey) and 8 (brown) respectively.
c. Plug one end of the Direct Connect Cord to the wireless dialer’s internal RJ31 jack.
d. Plug the other end of the Direct Connect Cord into the RJ31X jack.
c. Plug one end of the Direct Connect Cord to the wireless dialer’s internal RJ31 jack.
d. Plug the other end of the Direct Connect Cord into the RJ31X jack.
15.
Install the cover on the 5842 and secure it with the provided screw.
5842-002-V1
TELEPHONE IN
TELEPHONE OUT
INCOMING
PHONE LINE
INCOMING
PHONE LINE
DIRECT CONNECT
TELCO
TERMINATION
BLOCK
RJ31X
RJ11
FULL LINE SEIZURE CONNECTIONS
LOCAL LINE SEIZURE CONNECTIONS
DIRECT
CONNECT
DIRECT CONNECT
RJ31X
GRAY
RED
GREEN
BROWN
4
1
2
3
5
6
7
8
TO PREMISES PHONES
RING
TIP
RING
TIP
TO CONTROL PANEL
(FOR BACKUP
REPORTING)
(FOR BACKUP
REPORTING)
5842
TELEPHONE IN
TELEPHONE OUT
RJ31X
RJ11
5842
Figure 2 - 5842 Telephone Connections