Honeywell International Inc. 8DL5882-4 Manuale Utente
3
b. Verify that DIP switch #1 is in the OFF position.
c. Set DIP switch #5 according to the following chart.
DIP SWITCH #5
For . . .
Set to . . .
Commercial Fire Applications
ON
Non-commercial Fire Applications
OFF
NOTES:
•
If multiple receivers are used on one control, DIP
switch #5 must be set to the same position on all
receivers.
receivers.
•
DIP switch #5 reduces sensitivity during
supervision message reception. For commercial fire
applications, DIP switch #5 must be in the ON
position.
supervision message reception. For commercial fire
applications, DIP switch #5 must be in the ON
position.
5. Insert the wiring plug (with 4 flying leads) into the
mating socket on the receiver (see Figure 3 for socket
location). Connect the 4 wires to the control's
corresponding keypad terminals (see “Interface Wiring”
in the SPECIFICATIONS section).
location). Connect the 4 wires to the control's
corresponding keypad terminals (see “Interface Wiring”
in the SPECIFICATIONS section).
6. Install the antennas in the right-hand terminals of the
two terminal blocks at the upper edge of the circuit
board, one into each block’s right-hand terminal, and
tighten the screws to secure them.
board, one into each block’s right-hand terminal, and
tighten the screws to secure them.
Caution: Avoid mounting the receiver antennas against
a metal surface.
a metal surface.
7. Proceed with any programming of the control that
may be necessary for RF operation, and the
installation of the system's wireless transmitters,
as described in the control's installation and setup guide
and the transmitter's installation instructions.
installation of the system's wireless transmitters,
as described in the control's installation and setup guide
and the transmitter's installation instructions.
NOTES:
•
The receiver can support up to 16 encrypted wireless
transmitters (keys). The total quantity of wireless
keys (encrypted and unencrypted) that can be used is
determined by the control panel.
keys (encrypted and unencrypted) that can be used is
determined by the control panel.
•
Wireless key buttons must be enrolled to zones in the
control panel via zone programming first. If the
wireless key is to be used for arming and disarming
the VISTA-40 and up, a user number must then be
assigned to the wireless key via user programming. If
it is not done in this order, you will be unable to
respond successfully to the RF button zone number
prompt in user programming.
wireless key is to be used for arming and disarming
the VISTA-40 and up, a user number must then be
assigned to the wireless key via user programming. If
it is not done in this order, you will be unable to
respond successfully to the RF button zone number
prompt in user programming.
•
If more than one receiver is being used and you are
using encrypted wireless keys, we recommend that
you (a) enter the GO/NO GO mode, (b) disconnect one
receiver, (c) enroll all encrypted keys into the
connected receiver, (d) reconnect the disconnected
receiver, (e) exit the GO/NO GO mode, and then (f)
repeat (a) through (e) for the receiver that was
disconnected.
you (a) enter the GO/NO GO mode, (b) disconnect one
receiver, (c) enroll all encrypted keys into the
connected receiver, (d) reconnect the disconnected
receiver, (e) exit the GO/NO GO mode, and then (f)
repeat (a) through (e) for the receiver that was
disconnected.
•
The RED LED located on the receiver's circuit board
should be used as an indicator of strong local radio
frequency interference. If this LED is continuously
illuminated, the receiver should be relocated.
frequency interference. If this LED is continuously
illuminated, the receiver should be relocated.
•
After a successful enrollment of an encrypted key, the
GREEN LED blinks the number of spaces that are
free for additional encrypted key enrollment.
free for additional encrypted key enrollment.
8. Replace the receiver's cover.
ENCRYPTED KEYS
The receiver can support up to 16 encrypted wireless
transmitters (keys) at one time. If the number on the
receiver microprocessor is WAK 4406-4 or higher, the
receiver provides you with the capability to check space
available and/or delete encrypted keys using the procedures
below.
transmitters (keys) at one time. If the number on the
receiver microprocessor is WAK 4406-4 or higher, the
receiver provides you with the capability to check space
available and/or delete encrypted keys using the procedures
below.
The GREEN LED located on the receiver's circuit board
may be used to determine how many more encrypted keys
may be enrolled into the receiver. This LED is also used to
indicate when encrypted keys may be deleted. To determine
how many more encrypted keys may be enrolled and/or to
delete enrolled encrypted keys:
may be used to determine how many more encrypted keys
may be enrolled into the receiver. This LED is also used to
indicate when encrypted keys may be deleted. To determine
how many more encrypted keys may be enrolled and/or to
delete enrolled encrypted keys:
1. Remove power from the receiver and set DIP
switch 1 to the ON position.
2. Apply power to the receiver and watch the GREEN
LED. You will see one of the following indications:
a. The GREEN LED blinks the number of spaces that
are free for additional encrypted key enrollment and
then goes to constantly ON.
then goes to constantly ON.
b. The GREEN LED is constantly ON, indicating the
receiver is full.
c. The GREEN LED is OFF, indicating no encrypted
keys are enrolled.
3. If you do not want to delete any enrolled
encrypted keys, advance to step 4. If you want to
delete enrolled encrypted keys, wait until the
GREEN LED is constantly ON in step 2 a. or 2 b.
above and then:
delete enrolled encrypted keys, wait until the
GREEN LED is constantly ON in step 2 a. or 2 b.
above and then:
a. Record the positions of DIP switches 1 through
5.
b. Set DIP switches 1 through 5 to the opposite
positions of their current settings and wait a
few moments.
few moments.
c. Set DIP switches 1 through 5 back to their
original positions as recorded in step a. All
enrolled encrypted keys will be deleted.
enrolled encrypted keys will be deleted.
4. Place DIP switch 1 back into the OFF position to
return to normal receiver operation.