Conifer Corporation 2278 Manuale Utente
Ultraflex® Two-Way System
Packing List
(1) Response Antenna
Options
•
QD-2450
•
18T-2127
•
26T-2127
(1) Transverter
(1) Power Supply/Inserter
(1) GPS Antenna
(2) Transverter Mounting Brackets
(1) Power Supply/Inserter
(1) GPS Antenna
(2) Transverter Mounting Brackets
#726055 for inch pipe
#726044 for 1-2 inch O.D. pipe
#726044 for 1-2 inch O.D. pipe
(2) “L” Bolts #163155.2
Response Antenna Options
QD-2450
(2) #6 x 1/2” Stainless Screws
(2) #6 x 1/2” Stainless Screws
Model 26T-2127
FEED BOX
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2” stainless screw
(2) Stainless 1/4 x 20 hex nuts
(2) Stainless lock washers
(2) Stainless carriage bolts
FEED BOX
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2” stainless screw
(2) Stainless 1/4 x 20 hex nuts
(2) Stainless lock washers
(2) Stainless carriage bolts
REFLECTOR BOX
(2) Reflector halves
(2) Stainless U-bolts
(2) Mast clamps
(1) Mounting "L" shaped bracket
(4) Keps nuts
(4) #8-32 machine screws
(6) Stainless 1/4 x 20 hex nuts
(6) Stainless lock washers
(2) Stainless carriage bolts
(1) Stainless flat plate washer
(2) Reflector halves
(2) Stainless U-bolts
(2) Mast clamps
(1) Mounting "L" shaped bracket
(4) Keps nuts
(4) #8-32 machine screws
(6) Stainless 1/4 x 20 hex nuts
(6) Stainless lock washers
(2) Stainless carriage bolts
(1) Stainless flat plate washer
Model 18T-2127
FEED BOX
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2" stainless screw
(2) Stainless 1/4 x 20 x 1" carriage bolts
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2" stainless screw
(2) Stainless 1/4 x 20 x 1" carriage bolts
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
REFLECTOR BOX
(1) Reflector
(1) Mast clamp
(1) Mounting "L" shaped bracket
(1) Stainless U-bolt 1/4 x 20 x 2"
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
(1) Stainless flat plate washer
(1) Reflector
(1) Mast clamp
(1) Mounting "L" shaped bracket
(1) Stainless U-bolt 1/4 x 20 x 2"
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
(1) Stainless flat plate washer
#1
#2
#3
Page 2.
GPS Antenna
GPS Port
Antenna Port
(located on side
of transverter)
(located on side
of transverter)
Mounting
Bracket
“L” Bolt
Figure 10
Bracket
Chan-
nels
Input/Output
-20dB Test
Figure 9
0-20 dB
Attn.
Downstream
To “Ant”
To “Set”
Figure 11
Figure 8
11. Connect the downlead cable
to the input/output on the
Transverter. (See Figure
9.)
to the input/output on the
Transverter. (See Figure
9.)
Page 11.
10. Mount the Transverter on the
mast by sliding the mounting
bracketsand “L” Bolts into the
bracket channels on the
backside of the Transverter.
bracketsand “L” Bolts into the
bracket channels on the
backside of the Transverter.
(See Figure 10.)
12. Run the downlead to
the PS-0200 power supply
connector labeled “To
Ant”. (See Figure 11.)
the PS-0200 power supply
connector labeled “To
Ant”. (See Figure 11.)
13. Run a cable from the
PS-0200 power supply
connector labeled “To
Set” to the set-top.
(See Figure 11.)
PS-0200 power supply
connector labeled “To
Set” to the set-top.
(See Figure 11.)