Honeywell International Inc. 9PGTPL-100A Manuale Utente
Page 2012
1 Mar 2006
34-45-54
MAINTENANCE MANUAL
TPL-100A Processor / Part No. 940-0530-001
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.
(l) RA Status Inhibit
This strap on RBP pin 4G controls whether RA display status is active or inhibited.
When this pin is strapped (connected to RBP pin 7K), RA display status is
inhibited.
When this pin is strapped (connected to RBP pin 7K), RA display status is
inhibited.
(m) On Ground Intruder Disable
This strap on RBP pin 4F controls whether or not intruders determined to be
on-the-ground will be displayed when own aircraft is below 1,750 feet (radio
altitude). When strapped (connected to RBP pin 7K), intruders on the ground will
not be displayed when own aircraft is below 1,750 feet.
on-the-ground will be displayed when own aircraft is below 1,750 feet (radio
altitude). When strapped (connected to RBP pin 7K), intruders on the ground will
not be displayed when own aircraft is below 1,750 feet.
4.
Equipment Installation
A. MILACAS-FR Processor Installation
Mount the MILACAS-FR Processor with its mounting tray component. The mounting tray is
available with a fan assembly. This fan operates from 115 V, 400 Hz or 28 V dc. Operating
power for the 115 V 400 Hz fan comes from the MILACAS-FR Processor when power is
applied to the MILACAS-FR Processor unit.
available with a fan assembly. This fan operates from 115 V, 400 Hz or 28 V dc. Operating
power for the 115 V 400 Hz fan comes from the MILACAS-FR Processor when power is
applied to the MILACAS-FR Processor unit.
The mounting tray connector must be wired in accordance with the interconnect diagram
(Figure 2002) and the manufacturer's instructions.
(Figure 2002) and the manufacturer's instructions.
NOTE: To allow for inspection or repair of the connector assembly wiring, sufficient lead
length must be left so that when the mounting hardware for the rear connector
assembly is removed the rear connector assembly may be pulled forward several
inches. The installer must make a bend in the harness (at the rear connectors) to
permit water droplets, that might form on the harness due to condensation, to drip
off at the bend and not collect in the connector.
assembly is removed the rear connector assembly may be pulled forward several
inches. The installer must make a bend in the harness (at the rear connectors) to
permit water droplets, that might form on the harness due to condensation, to drip
off at the bend and not collect in the connector.
When locating the mount in the aircraft, allow at least two inches free space on the top and
sides of the unit to give sufficient clearance for sway and ease of removal of the
MILACAS-FR Processor. Clean all mounting surfaces prior to installation.
sides of the unit to give sufficient clearance for sway and ease of removal of the
MILACAS-FR Processor. Clean all mounting surfaces prior to installation.
Once the mounting tray is installed, the MILACAS-FR Processor unit may be easily
installed in the mounting tray. Put the MILACAS-FR Processor on the mounting base and
slide it forward until the electrical connector is fully engaged. Then tighten the two knurled
screw clamps (located on front of the mount) until they are firmly seated over the hold-down
hooks on the front of the MILACAS-FR Processor.
installed in the mounting tray. Put the MILACAS-FR Processor on the mounting base and
slide it forward until the electrical connector is fully engaged. Then tighten the two knurled
screw clamps (located on front of the mount) until they are firmly seated over the hold-down
hooks on the front of the MILACAS-FR Processor.
B. TCAS Directional Antenna Installation
(1) Directional antenna positioning and wiring requirements. Refer to paragraph 3.B.(1),
3.C.(5) and, 3.C.(6)(b).
(2) Directional antenna footprint drilling and mounting
Before mounting the antenna, make sure that aircraft mounting surface is clean.