IQ Group Ltd QS5-02WD3130 Manuale Utente

Figure 1

Transmitter 

Transmitter

Align arrow for 
installation 

Transmitter

Magnetic 
piece 

• 

Plug-In Alert 

• 

Magnetic Piece, Transmitter & CR2032 Lithium coin cell battery  

• 

4 screws and 4 wall plugs for mounting the Magnetic piece & Transmitter 

 

• 

A small Phillips head and Flat head screwdriver 

 

Installation Instructions 
For interior use only. 
Please note: Installing the Transmitter or plug-in alert on or near metal 
structures or reinforced PVC doors or doorframes may reduce the transmission 
range.   
 

Figure 1. 
Remove the front cover by inserting a flat head screwdriver 
into the slot and twist gently.  
 

Install the battery for Transmitter (Refer to Figure 2) 
Position the front cover as shown and slide the CR 2032 
Lithium battery into the holder as shown, with the + side of 
the battery facing you. 

  

Install the Transmitter and Magnetic piece 
Ensure the frame of the door or window is flat, clean 
and dry. Mount the bases using the screws and wall 
plugs provided (See Figure 3). Install both units 
vertically. Align the arrows make sure both the 
Magnetic piece and Transmitter are on the same level 
of surface (See Figure 1). Do not mount the 
Transmitter on or near large metal objects as this can 
block signals from the wireless Transmitter.  
 
Snap the front cover to the base. To 
ensure a good alignment, adjust the 
front cover of the Magnetic piece by 
pushing or pulling the cover in and out 
(3 adjustment levels).  
  

Install the Plug-in Alert (Refer to Figure 4) 
Plug the Plug-in Alert into any 120 VAC 
outlet in the house. The Plug-in Alert must be 
within 150 feet of the Transmitter. 

 The Plug-

in Alert will play 2-note and 1-note sounds 
when it is first powered up.  
  
 
 

(Refer to Figure 5) 
Program the Transmitter. Open the door or window.  A Ding-Dong should be 
heard indicating the transmitter has been programmed to the Alert.  Close the 
door or window.  A Ding should be heard.   The LED light (A) will illuminate 
indicating the transmitter is working. 

 

  

 
 
 
 
 
 
 
 
 
 
 
    

Range………………..up to 150 ft. 
Electrical Load………1 x CR2032 Lithium Battery for Transmitter 

Note: 
This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 

(1) 

This device may not cause harmful interference, and 

(2) 

This device must accept any interference received, including interference that 
may cause undesired operation. 

The changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.  To comply with FCC 
RF exposure compliance requirements, this device and its antenna must not be co-located or 
operated in conjunction with any other antenna or transmitter. 
 

To Reset the Alert Programming, press and hold 
button B in Figure 6 until the plug-in chime sounds. 
The chime will play the tunes available indicating 
that previous programs have been erased.  Return to the 
Program Transmitter to the Plug-in Alert section and  
repeat. 

 

 
 
                                     

Troubleshooting 

Figure 6 

Alert doesn’t sound when door or window is opened or closed 
Check that the battery has been inserted correctly. The LED light should 
come on when the Transmitter moves closer to or away from the Magnetic 
piece. 

Transmitter may be positioned out of range of the Plug-in Alert. Move 
the Plug-in Alert closer to the Transmitter. 
A metallic object may be blocking the signal to the Plug-in Alert from the 
Transmitter position. Experiment with the location of the Plug-in Alert to 
see if you can move it to a more suitable place. 

Figure 2

Magnetic 

Piece

Battery in the Transmitter may need replacing. 
The Transmitter LED will flash 5 times when the battery needs replacing. 
See instruction for Installing the Battery.  
Note: In cold conditions, poor location or environment, operating at 
maximum range it is advisable to replace the battery more frequently (i.e. 
every 12-18 months) to maintain optimum performance. 
Your Transmitter and Plug-in Alert haven’t been programmed. Reset the 
automatic programming of your Plug-in Alert by pressing and holding down 
button

 B (Figure 6) for 5 seconds.  The alert will sound indicating the 

programming has been erased.  Program the Transmitter following the 
installation instructions. 

3 adjustment 
levels

Figure 3 

For any other problem, call 1-800-296-1869 between 9am and 5pm EST. 

 
 
 
 
 

This is a “Limited Warranty” which gives you specific legal rights. You may also 

have other rights which vary from state to state and province to province. 

For a period of two years from the date of purchase, any malfunction caused by 

factory defective parts or workmanship will be corrected at no charge to you. To obtain 
a replacement, return the product to the place of purchase. 

NOT COVERED: Repair service, adjustment and calibration due to misuse, abuse 

or negligence. Unauthorized service or modification of the product or of any furnished 
component will void this warranty. This warranty does not include reimbursement for 
inconvenience, installation, setup time, loss of use or unauthorized service. 

This warranty covers only IQ America products and is not extended to other 

equipment and components that a customer uses in conjunction with our products. 

This warranty is expressly in lieu of all other warranties, express or implied, 

including any warranty, representation or condition of merchant ability or that the 
products are fit for any particular purpose or use, and specifically in lieu of all special, 
indirect or incidental or consequential damages. 

Repair or replacement shall be the sole remedy of the customer and there shall be no 

liability on the part of IQ America for any special, indirect, incidental or consequential 
damages, including but not limited to any loss of business or profit, whether or not 
foreseeable. Some states or provinces do not allow the exclusion or limitation of 
incidental or consequential damages, so the above limitation or exclusion may not 
apply to you. Retain receipt for warranty

 claims. 

Figure 4 

 

Figure 5

(WD

508

0-ACEPIKEP-N: MANL-WD

508

0-ACEPIKEP-N.ed4)

WD

5080:MANL-WD5080.ed1

I-MANL-IQAPLPWD5080

IQ: IM-WD-5080A(25-11-09)-1