ICOM 361500 Manuale Utente
1-3
1
PANEL DESCRIPTION
u
MICROPHONE CONNECTOR [MIC]
Accepts an optional microphone.
• See p. ?15-4 for appropriate microphones.
• See p. ?2-10 for microphone connector information.
• See p. ?2-10 for microphone connector information.
i
SD CARD SLOT [SD CARD]
(p. ??-?)
Insert the supplied SD card for both reading/storing a
wide variety of the transceiver’s information and data.
• The indicator beside the slot lights or blinks when the
transceiver reads or writes to the card.
• Push the card to remove the card card.
o
USB INDICATOR [USB]
Lights while accessing the USB flash drive inserted
to the [USB A] port.
!0
MONITOR GAIN CONTROL [MONI GAIN]
(p.
?6-4)
Adjusts the transmit IF signal monitor level.
!1
COMPRESSION LEVEL CONTROL [COMP]
(p. ?6-5)
Adjusts the speech compression level in SSB.
!2
DRIVE GAIN CONTROL [DRIVE]
(p. ?3-13)
Adjusts the transmitter level at the driver stage. Ac
-
tivate in all modes
(except SSB with [COMP] OFF)
.
!3
VOX GAIN CONTROL [VOX GAIN]
(p. ?6-2)
Adjusts the transmit/receive switching threshold
level for VOX operation.
level for VOX operation.
!4
ANTI VOX CONTROL [ANTI VOX]
(p. ?6-2)
Adjusts the VOX deactivate level to prevent un
-
wanted VOX activation from the speaker audio.
!5
DISPLAY CONTRAST CONTROL [CONTRAST]
Adjusts the display contrast.
!6
DISPLAY BRIGHTNESS CONTROL [BRIGHT]
Adjusts the display brightness.
!7
MONITOR KEY [MONI] (p. ?6-4)
Monitors your transmitted IF signal.
• The CW sidetone functions regardless of [MONI] key
setting in CW mode.
• The [MONI] indicator above this key lights white while
the function is activated.
!8
BREAK-IN DELAY CONTROL [DELAY]
(p. ?6-3)
Adjusts the transmit-to-receive switching delay time
for CW semi-break-in operations.
for CW semi-break-in operations.
!9
ELECTRONIC CW KEYER SPEED CONTROL
[KEY SPEED]
(p. ?4-4)
Adjusts the internal electronic CW keyer’s speed.
• 6 wpm (minimum) to 48 wpm (maximum) can be set.
• The keyer’s speed is displayed.
• The keyer’s speed is displayed.
@0
VOX/BREAK-IN KEY [VOX/BK-IN]
➥
Push to turn the VOX function ON or OFF in the
SSB, AM, or FM mode operation. (p. ?6-2)
➥
Push to turn the break-in function ON
(Semi
break-in, Full break-in)
or OFF during CW mode
operation. (p. ?6-3)
➥
Hold down for 1 second to enter VOX set screen.
(p. ?6-2)
✔
What is the VOX function?
The VOX function (voice operated transmission) starts trans
-
mission without pushing the transmit key or PTT switch when
you speak into the microphone; then, automatically returns
to receive when you stop speaking.
you speak into the microphone; then, automatically returns
to receive when you stop speaking.
✔
What is the break-in function?
The break-in function toggles between transmit and receive
with CW keying. Full break-in (QSK) can monitor the receive
signal during keying.
with CW keying. Full break-in (QSK) can monitor the receive
signal during keying.
@1
RF POWER CONTROL [RF PWR] (p. ?3-12)
Continuously varies the RF output power from min-
imum
imum
(5 W*)
to maximum
(200 W*)
.
*AM mode: 5 W to 50 W
• The output power is displayed.
• The output power is displayed.
@2
MIC GAIN CONTROL [MIC]
Adjusts microphone gain.
• The transmit audio tone in the SSB, AM, or FM mode
can be adjusted independently in the Level set screen.
(p. ?12-4)
✔
How to set the microphone gain.
Set the [MIC] control so that the ALC meter swings within
the ALC range during normal voice level transmission in the
SSB or AM mode. (The ALC meter must be selected.)
Recommended level for
an Icom microphone
an Icom microphone
Decreases
Increases