ICOM 366400 Manuale Utente
8
NXDN OPERATION <CONVENTIONAL MODE>
8-4
Transmitting a call (Continued)
Individual call
D
You can call a specified station that is set to the same
unit ID by using the Individual call function.
unit ID by using the Individual call function.
Push [Individual (NXDN)] to enter the Unit ID Select
q
mode.
• Displays “SELCALL.”
SELCALL
UID 0001
Push [UP] or [DOWN] to select a desired unit ID.
w
• If you want to directly enter an unit ID, push [P2](MODE)
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
Push [P3](TX) or [PTT] to make the Individual call.
e
Push [P1](EXIT).
r
For your reference:
When [Individual + SDM (NXDN)] or [Individual + Sta-
tus (NXDN)] is assigned, you can send a message
along with an Individual call.
When [Individual + SDM (NXDN)] or [Individual + Sta-
tus (NXDN)] is assigned, you can send a message
along with an Individual call.
To send a Short Data Message with an Individual call.
Push [Individual + SDM (NXDN)] to enter the unit ID
q
Select mode.
• Displays “SELCALL.”
Push [UP] or [DOWN] to select a desired unit ID.
w
Push [P1](ENT).
e
• Enters the Short Data Message Entry mode.
Push [UP] or [DOWN] to enter a character, and then
r
push [P1](SET) to set.
• Goes to the next character entry position.
• You can use the 10-keypad keys on the microphone.
• You can use the 10-keypad keys on the microphone.
Repeat step
t
r
until you enter a message of up to
100 characters.
• Push [P0](DEL) to delete a character.
• Push [P2](Ω) or [P3](≈) left or right to select a charac-
• Push [P2](Ω) or [P3](≈) left or right to select a charac-
ter.
SHORT MESSAG
Push [PTT] to send the message to the selected
y
unit ID.
Push [P1](EXIT) to exit.
Push [P1](EXIT) to exit.
u
To send a Status Message with an Individual call.
Push [Individual + Status (NXDN)] to enter the unit
q
ID Select mode.
• Displays “SELCALL.”
Push [UP] or [DOWN] to select a desired unit ID.
w
Push [P1](ENT).
e
• Enters the Status Message Entry mode.
Push [UP] or [DOWN] to select a desired status
r
message.
• If you want to directly enter a status message, push [P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
• You can use the 10-keypad keys on the microphone.
• You can use the 10-keypad keys on the microphone.
STATUS
STATUS 001
Push [P3](TX) or [PTT] to send the message to the
t
selected unit ID.
Push [P1](EXIT) to exit.
Push [P1](EXIT) to exit.
y
Individual Call Acknowledge Request call
D
When the Individual Call Acknowledge Request func-
tion is set, you can transmit an acknowledgement re-
quest signal with the Individual call.
Therefore, you can confirm whether the transceiver is
located in the communication range or not.
tion is set, you can transmit an acknowledgement re-
quest signal with the Individual call.
Therefore, you can confirm whether the transceiver is
located in the communication range or not.
Push [Individual (NXDN)] to enter the Unit ID Select
q
mode.
• Displays “SELCALL.”
Push [UP] or [DOWN] to select a desired unit ID.
w
• If you want to directly enter an unit ID, push [P2](MODE)
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
Push [P3](TX) or [PTT] to make the Individual call
e
with an acknowledgement request signal.
• Displays “CALLING,” and then after receiving an acknowl-
edgement, displays “HOLDING.”
When the called station calls back, the transceiver
r
displays the called station’s unit ID.
• Displays “NO REPLY” and sounds error beeps when your
transceiver does not receive an acknowledgement within
the preset time period.
the preset time period.