ICOM 376902 Manuale Utente

– 2 –

– 3 –

W ARNING

Your Icom radio generates RF

electromagnetic energy during transmit

mode. This radio is designed for and

classified as “Occupational Use Only”,

meaning it must be used only during the

course of employment by individuals aware

of the hazards, and the ways to minimize

such hazards. This radio is NOT intended

for use by the “General Population” in an

uncontrolled environment.

• For compliance with FCC and IC RF Exposure

Requirements, the transmitter antenna installation shall

comply with the following three conditions:

1. The transmitter antenna gain shall not exceed 0 dBi.

2. IC-F5400D series:

The antenna is required to be located outside of a

vehicle and kept at a distance of 52 centimeters (21

inches) or more between the transmitting antenna

of this device and any persons during operation. For

small vehicle as worst case, the antenna shall be

located on the roof top at any place on the center line

along the vehicle in order to achieve 52 centimeters

(21 inches) separation distance. In order to ensure this

distance is met, the installation of the antenna must

be mounted at least 52 centimeters (21 inches) away

from the nearest edge of the vehicle in order to protect

against exposure to bystanders.

2. IC-F6400D series:

The antenna is required to be located outside of a

vehicle and kept at a distance of 38 centimeters

(15 inches) or more between the transmitting antenna

of this device and any persons during operation. For

small vehicle as worst case, the antenna shall be

located on the roof top at any place on the center line

along the vehicle in order to achieve 38 centimeters

(15 inches) separation distance. In order to ensure this

distance is met, the installation of the antenna must

be mounted at least 38 centimeters (15 inches) away

from the nearest edge of the vehicle in order to protect

against exposure to bystanders.

3. IC-F5400D series:

Transmit only when people outside the vehicle are

at least the recommended minimum distance of

125 centimeters (49 inches) away from the properly

installed antenna. This separation distance will

ensure that there is sufficient distance from a properly

installed externally-mounted antenna to satisfy the RF

exposure requirements in the applicable RF exposure

compliance standards.

3. IC-F6400D series:

Transmit only when people outside the vehicle are

at least the recommended minimum distance of

109 centimeters (43 inches) away from the properly

installed antenna. This separation distance will

ensure that there is sufficient distance from a properly

installed externally-mounted antenna to satisfy the RF

exposure requirements in the applicable RF exposure

compliance standards.

CAU TION

To ensure that your exposure to RF

electromagnetic energy is within the FCC

and IC allowable limits for occupational

use, always adhere to the following

guidelines:

•

DO NOT operate the radio without a proper antenna

attached, as this may damage the radio and may also

cause you to exceed FCC and IC RF exposure limits. A

proper antenna is the antenna supplied with this radio by

the manufacturer or an antenna specifically authorized by

the manufacturer for use with this radio.

•

DO NOT transmit for more than 50% of total radio use

time (“50% duty cycle”). Transmitting more than 50% of

the time can cause FCC and IC RF exposure compliance

requirements to be exceeded. The radio is transmitting

when the status indicator lights red. You can cause the

radio to transmit by pressing the “PTT” switch.

Electromagnetic Interference/Compatibility

During transmissions, your Icom radio generates RF energy

that can possibly cause interference with other devices or

systems. To avoid such interference, turn off the radio in

areas where signs are posted to do so.

DO NOT operate

the transmitter in areas that are sensitive to electromagnetic

radiation such as hospitals, aircraft, and blasting sites.

SAFETY TRAINING INFORMATION

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France,

Spain, Russia, Australia, New Zealand, and/or other countries.

AMBE+2 is a trademark and property of Digital Voice Systems Inc.

All other products or brands are registered trademarks or trademarks of their respective holders.

ISO 3166-1

Country

Codes

Country

Codes

Austria

Belgium

Bulgaria

Croatia

Czech Republic

Cyprus

Denmark

Estonia

Finland

France

Germany

Greece

Hungary

Iceland

Ireland

Italy

Latvia

Liechtenstein

Lithuania

Luxembourg

Malta

Netherlands

Norway

Poland

Portugal

Romania

Slovakia

Slovenia

Spain

Sweden

Switzerland

Turkey

United Kingdom

< Intended Country of Use >

COUNTRY CODE LIST