Doodle Labs Pte Ltd NM-2450-2F Manuale Utente
TECHNICAL SPECIFICATIONS
Model No.
Model No.
NM-2450-2F (802.11n, ath9k driver)
MAC Chipset
11n Models – Qualcomm Atheros
QCA9590-AR1B with Extended Temperature range for Outdoor and
Rugged models)
QCA9590-AR1B with Extended Temperature range for Outdoor and
Rugged models)
Software Support
Linux Driver
Center Frequency Range
2.412 GHz ~ 2.484 GHz
This varies by the regulatory domain
This varies by the regulatory domain
Channel Bandwidth*
20, and 40 MHz channels
Radio Modulation (Auto
Adjust)
Adjust)
CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz – 11n models)
Data Rates Supported
: MCS0-23
: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz)
802.11n version 2.0
Capabilities
Capabilities
802.11n and b/g Beam Forming
Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal
ratio combining (MRC), Cyclic shift diversity (CSD), Frame
aggregation, block ACK, 802.11e compatible bursting, Spatial
multiplexing, cyclic-delay diversity (CDD), low-density parity check
(LDPC), Space Time Block Code (STBC)
ratio combining (MRC), Cyclic shift diversity (CSD), Frame
aggregation, block ACK, 802.11e compatible bursting, Spatial
multiplexing, cyclic-delay diversity (CDD), low-density parity check
(LDPC), Space Time Block Code (STBC)
Operating Modes
AP, STA and Adhoc modes to implement Point to Point, Point to multi
Point
Point
MAC Protocol
TDD with Carrier Sense Multiple Access with Collision Avoidance
(CSMA/CA)
(CSMA/CA)
Wireless Error Correction
FEC, ARQ
Wireless Data Security
128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for
IEEE 802.11d, e, h, i, k, r, v, w and time stamp standards
IEEE 802.11d, e, h, i, k, r, v, w and time stamp standards
FIPS Certification
Loop back mode to facilitate FIPS AES certification, Small packet size
(96 bytes) in AES encryption at full packet rate
(96 bytes) in AES encryption at full packet rate
Tx/Rx
Specification
Specification
Radio
Modulation
Coding
Rate
Max Tx Power
(± 2 dB)
Rx Sensitivity
(Typ)
20 MHz Channel – 11n models
802.11b, STBC
CCK
1/2
28
-100
802.11b, STBC
64 QAM
3/4
26
-80
MIMO
BPSK
1/2
28
-92
MIMO
16 QAM
3/4
28
-82
MIMO
64 QAM
5/6
26
-72
40 MHz Channel – 11n models
MIMO
BPSK
1/2
28
-90
MIMO
16 QAM
3/4
28
-79
MIMO
64 QAM
5/6
26
-70
* It is advantageous to use the smallest Channel Bandwidth that can support the Throughput
requirements. Smaller bandwidths provide more channels to choose and help avoid interference
issues. The system’s SNR is higher at smaller Channel Bandwidths and Range is longer.
Antenna Signal
Strength
requirements. Smaller bandwidths provide more channels to choose and help avoid interference
issues. The system’s SNR is higher at smaller Channel Bandwidths and Range is longer.
Antenna Signal
Strength
-35 dBm to -85 dBm (Recommended), (Absolute Maximum=+12 dBm)
Antenna port
isolation for
concurrent
operation
isolation for
concurrent
operation
+10 dBm signal strength for 5 GHz signal without degrading 2.4 GHz operation
Integrated Antenna >20 KV (Human Body Model)