Eurochron Watch (EQAC 331 9146c25b) EQAC 331 9146c25b Scheda Tecnica

The product displays the time and date and also has a stopwatch feature.

Always observe the safety instructions and all other information included in these 
operating instructions.

This product complies with the applicable national and European regulations. All 
names of companies and products are the trademarks of the respective owners. All 
rights reserved.

-

 Quartz wristwatch

-

 Operating instructions



   Please read all of the operating instructions before using the product 

-

   For safety reasons, any unauthorised conversion and/or modifi cation of the 

product is not permitted. Never dismantle the product.

-

   This product is not a toy and does not belong in the hands of children. The pro-

duct contains small parts that could be swallowed and a battery.

-

   Do not leave the packaging materials unattended. They may become dangerous 

playthings for children.

-

   Handle the product with care; it can be damaged by impacts, blows, or accidental 

drops, even from a low height.

-

  Normal/rechargeable batteries do not belong in the hands of children.

-

   Do not leave batteries/rechargeable batteries lying around; there is a risk of 

being swallowed by children or pets. If they are swallowed, consult a doctor 
immediately.

-

   Leaking or damaged batteries/rechargeable batteries in contact with the skin 

can cause acid burns; therefore, use suitable safety gloves.

-

   Batteries/rechargeable batteries must not be short-circuited, opened or thrown 

into fi re. There is a risk of explosion!

-

   Do not recharge normal, non-rechargeable batteries; risk of explosion! Only 

charge rechargeable batteries that are intended for this purpose; use a suitable 
battery charger.

-

   Check that the polarity is correct when inserting the batteries (pay attention to 

plus/+ and minus/-!).

(A) Stopwatch minute display

(B) Stopwatch second display

(C) Date display

(D) 24h display

(E) Winder

-

   Bring the winder (E) to position 2 and set the current time by turning the winder 

(E).

   

   

The second hand stops, in order to allow the seconds to be set correctly.

 

 When setting, also pay attention to correct setting of the 24h display (D).

-

   Bring the winder (E) to position 1 and set the current date (C) by turning the 

winder (E) clockwise.





If the date is set between 21:00 and 1:00 hours, the date may not change on 
the following day.

 

 Do not press the buttons S1   and S2 not, while the winder (E) is pulled out, 
otherwise the zero position of the stopwatch display may change.

-

   Push the winder (E) back to its normal position.

With the 24 hour display (D), the time (only hours) is not displayed as in normal 
analogue clock in 12h format, but 24h format. You can also read if it’s day or night 
right then.





When using the stopwatch, make sure that the hands of the stopwatch 
displays (A) and (B) are in the zero position (12 o’clock position) prior to 
start.

 

The stopwatch can measure a time interval of up to 60 minutes.

-

   Start the stopwatch by pressing S1.

-

   Stop the stopwatch by pressing S1 again.

-

   An adding function is available, when it is started and stopped several times, by 

pressing S1.

-

   Reset after stop is done by pressing S2.

-

   The elapsed time is indicated by the minutes display (A) and the seconds display 

(B).

-

   When the stopwatch is running, an interval may be included by pressing S2.

 

 The time measurement continues, but the hands are stopped. If S2 is pressed 
again, the hands of the stopwatch run fast on the current time kept.

If the stopwatch hands do not return to the 12 o’clock position after being reset, they 
must be set manually. This may happen e.g. after a blow or replacing the batteries.

-

   Pull the winder (E) to position 2.

-

   Set the hands of the stopwatch by pressing S1 or S2 to zero position (12 o‘clock 

position).

 

 S1 moves the hand counter-clockwise, S2 moves it clockwise. If you press and 
hold S1 or S2, the hands run in fast mode.

-

   Then press the winder (E) back into its normal position.





 Never press the winder back to its normal position while the second hand of 
the chronograph (2) is still returning to the zero position.

 

 The second hand will stop in the position it has when you press the winder 
back into normal position, and this new position of the second hand is then 
identifi ed as the zero position.