Extech Anemometer SDL310 Scheda Tecnica
Codici prodotto
SDL310
7
SDL310-EU-EN-V1.2-12/11
Setup Mode
Basic settings at a glance
To view the current configuration of the meter with regard to time, date, thermocouple type, and
datalogging sampling rate, press the SET/CLOCK ICON key momentarily. The meter will now
display the configuration in quick succession. Repeat as necessary to observe all of the information.
datalogging sampling rate, press the SET/CLOCK ICON key momentarily. The meter will now
display the configuration in quick succession. Repeat as necessary to observe all of the information.
Accessing the Setup mode
1.
Press and hold the SET key for at least 1.5 seconds to access the Setup menu.
2.
Press the SET key momentarily to step through the available parameters. The parameter type
is shown on the bottom of the LCD and the current selection for that type is shown above it.
is shown on the bottom of the LCD and the current selection for that type is shown above it.
3.
When a parameter is displayed that is to be changed, use the arrow keys to change the
setting. Press the ENTER key to confirm a change.
setting. Press the ENTER key to confirm a change.
4.
Press and hold the SET key for at least 1.5 seconds to exit the Setup mode. Note that the
meter automatically switches out of the Setup mode if no key is pressed in 7 seconds while in
the Setup mode.
meter automatically switches out of the Setup mode if no key is pressed in 7 seconds while in
the Setup mode.
5.
The available Setup parameters are listed below. Additional detailed information is provided
below this list:
below this list:
dAtE Set the clock time (Year/Month/Date; Hour/Minute/Second)
SP-t
Set the datalogger sampling rate (1 to 3600 Seconds)
PoFF Automatic power-off management
bEEP Set beeper sound ON/OFF
dEC
Set SD card Decimal character (comma for European format)
Sd F
SD memory card Format
t-CF
Select the Temperature unit of measure to C or F
tYPE Select the thermocouple type to K or J
Setting the Clock Time
1.
Access the dAtE parameter.
2.
Use the arrow keys to change a value
3.
Use the ENTER button to step through the selections
4.
Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
5.
The clock will keep accurate time even when the meter is switched off. However, if the battery
expires the clock will have to be reset after fresh batteries are installed.
expires the clock will have to be reset after fresh batteries are installed.
Setting the Datalogger Sampling Time (Rate)
1.
Access the SP-t parameter.
2.
Use the arrow keys to select the desired sampling rate. The available settings are: 0, 1, 2, 5, 10,
30, 60, 120, 300, 600, 1800, and 3600 seconds.
30, 60, 120, 300, 600, 1800, and 3600 seconds.
3.
Press the ENTER key to confirm the entry.
4.
Press and hold the SET key for at least 1.5 seconds to exit to the normal operation mode (or
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
Enabling/Disabling the Auto Power OFF Feature
1.
Access the PoFF parameter .
2.
Use the arrow keys to select ON (enable) or OFF (disable). With the Auto Power OFF feature
enabled, the meter will automatically switch OFF after 5 minutes of inactivity.
enabled, the meter will automatically switch OFF after 5 minutes of inactivity.
3.
Press ENTER to confirm setting.
4.
Press and hold the SET key for at least 1.5 seconds to exit to the normal operation mode (or
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).