ALIGN RH45E13X Scheda Tecnica
Important Notes
for models in the Align T-REX series
Make sure you read this safety information BEFORE building your model. Always keep to the procedures and settings
recommended in the instructions.
Safety Notes
•
Radio-controlled models are not toys in the usual sense of the term. Young persons under fourteen years should only be
allowed to operate them under the supervision of an adult.
•
Building and operating these models requires technical expertise, manual skills, a careful attitude and safety-conscious
behaviour. Errors, negligence and omissions in building or flying these models can result in serious personal injury and dama-
ge to property.
•
Since the manufacturer and vendor are not in a position to check that your models are built and operated correctly, all we can
do is bring these hazards expressly to your attention. We deny all further liability.
•
Helicopter rotors, and all moving parts generally, constitute a constant injury hazard. It is essential to avoid touching
such parts.
•
Please bear in mind that motors and speed controllers may become hot when operating. It is essential to avoid
touching such parts.
•
Do not stand close to the hazard area around rotating parts when an electric motor is connected to the flight battery.
You must also take care to keep all other objects away from moving or rotating parts.
•
Observe the instructions provided by the battery manufacturer. Overcharged or incorrectly charged batteries may
explode. Take care to maintain correct polarity.
Dear customer,
Many thanks for your decision to purchase one of our products, and the trust you have shown in us. These instructions summarise
all the relevant safety notes including the essential assembly notes relating to all T-REX helicopters. If your T-REX kit does not inclu-
de type-specific assembly instructions, you can request a copy by e-mail using the following address: align-manual@robbe.com.
Please be sure to state the serial number and the article number in your e-mail message, since we cannot process your
request without this information.
Yours sincerely,
Your robbe Modellsport Team
Before assembling and operating an Align model be sure to read the instructions supplied with the radio control
system, the battery charger and all the other electronic components as well as all the Safety Notes.
system, the battery charger and all the other electronic components as well as all the Safety Notes.
Caution - injury hazard: Please keep your model helicopter a safe distance away from you and others, including
other small co-axial and single-rotor models. Never fly over spectators, other pilots or yourself. Always fly mano-
euvres facing away from other pilots and spectators. Please note that model helicopters generally, and aerobatic
types in particular, are subject to enormous flight loads, and that interference cannot be ruled out even when you
are using the best possible radio control system components. Operating this type of model calls for a responsible
attitude and all possible safety precautions to protect pilots and spectators.remove all traces of oil from screwed
metal - metal joints, and apply T22, T43 or R48 thread-lock fluid (supplied in the set) sparingly before tightening
them, as described in the English instructions.
Re-tighten all screws firmly. Take care not to over-tighten screws which have to be driven into plastic."
Conformity Declaration
other small co-axial and single-rotor models. Never fly over spectators, other pilots or yourself. Always fly mano-
euvres facing away from other pilots and spectators. Please note that model helicopters generally, and aerobatic
types in particular, are subject to enormous flight loads, and that interference cannot be ruled out even when you
are using the best possible radio control system components. Operating this type of model calls for a responsible
attitude and all possible safety precautions to protect pilots and spectators.remove all traces of oil from screwed
metal - metal joints, and apply T22, T43 or R48 thread-lock fluid (supplied in the set) sparingly before tightening
them, as described in the English instructions.
Re-tighten all screws firmly. Take care not to over-tighten screws which have to be driven into plastic."
Conformity Declaration
robbe Modellsport GmbH & Co. KG hereby declares that this device conforms to the fundamental requirements and other
relevant regulations of the appropriate CE Directive. You can read the original Conformity Declaration on the Internet at
www.robbe.com, click on the „Conform“ Logo button which you will find next to the corresponding device description.
relevant regulations of the appropriate CE Directive. You can read the original Conformity Declaration on the Internet at
www.robbe.com, click on the „Conform“ Logo button which you will find next to the corresponding device description.
5
Disposal of used equipment
This symbol means that it is essential to dispose of electrical and electronic equipment separately from the domestic
refuse when it reaches the end of its useful life. Take your unwanted equipment to your local communal collection point or
recycling centre. This applies to all countries of the European Union, and to other European countries with separate waste
collection systems.