Superchips Inc. Car Stereo System 1715 maz Manuale Utente
Page 13 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
No Start after Programming? Don’t Panic!
In some vehicles equipped with the Passive Anti-Theft System or PATS, once the MAX
MicroTuner begins saving the factory stock program, the THEFT light begins blinking
rapidly and may even blink in short and long pulses to alert the user to a problem. Since
the Superchips MAX MicroTuner is communicating directly with the PCM, no other devices
may interrupt. As a result, the PATS module flags this as an error or theft condition and
goes into ‘THEFT’ mode. After the MAX MicroTuner has completed the programming
cycle, the PCM is still fully able to communicate and appears normal. However, the vehicle
may be in a No Start Condition and the THEFT light will be blinking rapidly.
MicroTuner begins saving the factory stock program, the THEFT light begins blinking
rapidly and may even blink in short and long pulses to alert the user to a problem. Since
the Superchips MAX MicroTuner is communicating directly with the PCM, no other devices
may interrupt. As a result, the PATS module flags this as an error or theft condition and
goes into ‘THEFT’ mode. After the MAX MicroTuner has completed the programming
cycle, the PCM is still fully able to communicate and appears normal. However, the vehicle
may be in a No Start Condition and the THEFT light will be blinking rapidly.
Corrective Procedure
This procedure should recover the vehicle and allow it to be started. Therefore, it is
recommended that the MAX MicroTuner programming cycle be completed prior to
recovery. i.e. The user should allow the MAX MicroTuner to upload the stock program and
should select their choice of performance files and any user options, if available. Following
instructions, they should complete the programming process.
recommended that the MAX MicroTuner programming cycle be completed prior to
recovery. i.e. The user should allow the MAX MicroTuner to upload the stock program and
should select their choice of performance files and any user options, if available. Following
instructions, they should complete the programming process.
Once the vehicle has been programmed with the selected performance program, complete
the following steps to reset the PATS THEFT condition if necessary.
the following steps to reset the PATS THEFT condition if necessary.
Disconnect the Superchips MAX MicroTuner & cable from the vehicle computer interface
connector.
connector.
If the vehicle will not start and the Theft Light is blinking rapidly
1.
Remove the Ground (-) cable from the battery post for a period of fifteen minutes to
allow the vehicle DTC codes and Theft codes to clear.
allow the vehicle DTC codes and Theft codes to clear.
2.
Re-attach the Ground cable to the battery and start the vehicle as you normally would.
Error Notification
In the event the programming cycle is interrupted, the MAX MicroTuner is designed to
recover automatically. Follow the on-screen prompts. If for any reason the MAX
MicroTuner fails to complete its programming cycle, an error message will be displayed
on the unit. Please make note of the message displayed and contact Superchips
Customer Service. If you need assistance please contact your local dealer or call
Superchips Customer Service at (407) 585-7000, M-F 8:00 AM till 5:00 PM. EST.
recover automatically. Follow the on-screen prompts. If for any reason the MAX
MicroTuner fails to complete its programming cycle, an error message will be displayed
on the unit. Please make note of the message displayed and contact Superchips
Customer Service. If you need assistance please contact your local dealer or call
Superchips Customer Service at (407) 585-7000, M-F 8:00 AM till 5:00 PM. EST.
11.
Special Instructions for Disabling the Fuel System in 2003 and Later
Ford Expeditions & Lincoln Navigators
Ford Expeditions & Lincoln Navigators
The Ford Motor Company requires that a connector be unplugged under the hood to
disable the fuel system. There is no need to remove any fuses. The fuel system connector
is located in the Power Train Control Module located under the hood on the passenger side
firewall. To disable the fuel system, with the ignition OFF, unplug the center plug only from
disable the fuel system. There is no need to remove any fuses. The fuel system connector
is located in the Power Train Control Module located under the hood on the passenger side
firewall. To disable the fuel system, with the ignition OFF, unplug the center plug only from
this module by pulling down on the
connector lever as shown in the figure
below.
Remember to reconnect the plug when
directed to do so by the MAX
MicroTuner.
connector lever as shown in the figure
below.
Remember to reconnect the plug when
directed to do so by the MAX
MicroTuner.
Figure 9
Page 14 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.