Superchips Inc. Car Stereo System 1715 maz Manuale Utente
Page 11 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
After the present program has been erased, the MAX MicroTuner will blink the following
message:
message:
Install TUNING
The bottom line of the display shows the programming progress.
9.
End of Programming Sequence
The programming sequence is now complete. Once the programming sequence has been
successfully accomplished on a vehicle, the MAX MicroTuner becomes LOCKED to that
vehicle. The MAX MicroTuner may not be used to tune any other vehicle. The MAX
MicroTuner may be used on other Ford vehicles as a DTC Reader.
successfully accomplished on a vehicle, the MAX MicroTuner becomes LOCKED to that
vehicle. The MAX MicroTuner may not be used to tune any other vehicle. The MAX
MicroTuner may be used on other Ford vehicles as a DTC Reader.
When the programming sequence is completed the MAX MicroTuner beeps and will display:
Please Wait…
The MAX MicroTuner is testing to see if the Passive Anti-Theft System is active. If PATS is
active the MAX MicroTuner beeps and displays the message:
active the MAX MicroTuner beeps and displays the message:
Resetting PATS
Please Wait...
Please Wait...
If Returning to Stock, and PATS is not active, the MAX MicroTuner automatically clears the
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages:
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages:
Clearing DTCs
then
TUNING Installed
Please Wait…
Turn Ign OFF
then
Remove the Ford
then
Enable the
MAX Tuner…
FUEL System…
Turn the ignition OFF and remove the cable from the diagnostic port.
10.
Return to Stock Sequence
The Return to Stock Sequence is used to reprogram a vehicle previously tuned with the
Superchips MAX MicroTuner with its original stock tuning. Follow the steps described in
Connecting the Superchips MAX MicroTuner to your vehicle in section 1. Following the
typical start up messages, if the MAX MicroTuner has been previously used to program a
vehicle, the MAX MicroTuner will beep and display:
Superchips MAX MicroTuner with its original stock tuning. Follow the steps described in
Connecting the Superchips MAX MicroTuner to your vehicle in section 1. Following the
typical start up messages, if the MAX MicroTuner has been previously used to program a
vehicle, the MAX MicroTuner will beep and display:
MicroTuner is
VIN Locked
VIN Locked
This indicates the MAX MicroTuner has been previously used to program a vehicle. It
should not be used to program another vehicle. The MAX MicroTuner will continue to
operate normally on the original vehicle.
should not be used to program another vehicle. The MAX MicroTuner will continue to
operate normally on the original vehicle.
After establishing communications, the MAX MicroTuner will display the following message:
RETURN to STOCK?
YES or NO
YES or NO
If ‘NO’ is pressed, the
MAX MicroTuner will return to Installing the Superchips
Performance Program at Step 5 above.
IMPORTANT NOTE
You MUST disable the fuel system before attempting to install a Performance
Program or to return the vehicle to its STOCK condition. Failing to do so can cause
serious damage to your engine that is not covered by the Superchips warranty.
Program or to return the vehicle to its STOCK condition. Failing to do so can cause
serious damage to your engine that is not covered by the Superchips warranty.
Page 12 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
If the ‘YES’ key is pressed it will beep once and display the following message:
Turn Ignition
OFF Press >
OFF Press >
Turn the ignition to the OFF position and press the ‘>’ key on the keypad.
The MAX MicroTuner will beep and blink the following message for approximately 6
seconds:
seconds:
Initialization..
Please Wait…
Please Wait…
After initialization is complete, the MAX MicroTuner will beep and display the message:
Turn Ignition ON
Do NOT START Eng
Do NOT START Eng
Turn the ignition to the ON position. The MAX MicroTuner will beep and display the
following messages:
following messages:
Ready to RETURN
then
Do NOT turn OFF
to STOCK
the IGNITION!!!
then
Press >
to Continue…
to Continue…
Press ‘>’. The MAX MicroTuner will beep once and erase the present program. The MAX
MicroTuner will blink the following message:
MicroTuner will blink the following message:
Erasing Present
Program...
Program...
After the program has been erased, the MAX MicroTuner will blink the following message:
Return To STOCK
The bottom line of the display shows the programming progress.
When the programming sequence is completed the MAX MicroTuner beeps and will display:
Please Wait…
The MAX MicroTuner is testing to see if the Passive Anti-Theft System is active. If PATS is
active the MAX MicroTuner beeps and displays the message:
active the MAX MicroTuner beeps and displays the message:
Resetting PATS
Please Wait...
Please Wait...
If Returning to Stock, and PATS is not active, the MAX MicroTuner automatically clears the
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages:
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages:
Clearing DTCs
then
TUNING Installed
Please Wait…
Turn Ign OFF
then
Remove the Ford
then
Enable the
MAX Tuner…
FUEL System…
Turn the ignition OFF and remove the MAX MicroTuner cable.