Korg D3200 Manuale Utente
95
Recovery
CD
Synchronizing two D3200 units
Here’s how you can make two D3200 units play back in sync.
One D3200 will be the MTC master, and the other will be the
MTC slave.
One D3200 will be the MTC master, and the other will be the
MTC slave.
(1) Use a MIDI cable to connect your equipment.
Use MIDI cables to connect the MIDI IN connectors and
MIDI OUT connectors of the master and slave D3200
units to each other.
MIDI OUT connectors of the master and slave D3200
units to each other.
(2) Make settings on the master D3200.
In the SYSTEM/MIDI, “MIDI/MMC” tab page, set
“MIDI Sync”
“MIDI Sync”
to “MTC Master,” and set “MMC Mode”
to “Receive.”
For this example, set “Device ID” to “10.”
For this example, set “Device ID” to “10.”
(3) Make settings on the slave D3200.
In the SYSTEM/MIDI, “MIDI/MMC” tab page, set
“MIDI Sync”
“MIDI Sync”
to “MTC Slave,” and set “MMC Mode”
to “Transmit.” Set “Device ID” to “10” to match the set-
ting of the master device.
ting of the master device.
If you don’t want to transmit or receive mixer control messag-
es, disable control change transmission and reception
(
es, disable control change transmission and reception
(
(4) Press the PLAY key of the slave D3200 unit.
An MMC message will be transmitted from the slave
D3200 unit. The master unit will receive this message,
and will start playing. When playback begins, the master
unit will transmit MTC, and when the slave unit
achieves synchronization, it will begin playback.
D3200 unit. The master unit will receive this message,
and will start playing. When playback begins, the master
unit will transmit MTC, and when the slave unit
achieves synchronization, it will begin playback.
It may take several seconds for synchronization to be
achieved.
achieved.
The D3200 supports multiple frame rates. The transmitting
and receiving devices must both be set to the same frame rate.
and receiving devices must both be set to the same frame rate.
Using MIDI to control the mixer
Recording D3200 mixer operations on your external MIDI
sequencer
sequencer
(1) Use a MIDI cable to connect the two devices.
Use a MIDI cable to connect the D3200’s MIDI OUT
connector to the MIDI IN connector of your external
MIDI sequencer.
connector to the MIDI IN connector of your external
MIDI sequencer.
(2) Adjust the synchronization settings on the D3200 and
on your external MIDI sequencer.
Access the SYSTEM/MIDI, “MIDI/MMC” tab page,
and set “MIDI Sync” to “MIDIClockMaster” or “MTC
Master.”
Adjust the synchronization settings on your external
MIDI sequencer as well. (For details, refer to the manual
of your MIDI sequencer.)
Access the SYSTEM/MIDI, “MIDI/MMC” tab page,
and set “MIDI Sync” to “MIDIClockMaster” or “MTC
Master.”
Adjust the synchronization settings on your external
MIDI sequencer as well. (For details, refer to the manual
of your MIDI sequencer.)
(3) Enable control change transmission on the D3200.
• In the SYSTEM/MIDI, “MIDI/MMC” tab page, click
the “MIDI” parameter “Control Change” to turn it
on.
on.
• If you want scene change data and mixer parameter
changes created by event automation playback to be
transmitted, turn the SCENE, “Automation” tab page
“Automation”
transmitted, turn the SCENE, “Automation” tab page
“Automation”
parameter on, and also click the SYS-
TEM/MIDI “MIDI/MMC”
tab page “MIDI” “Pro-
gram Change”
parameter to turn it on.
(4) Put the external MIDI sequencer in record-ready
mode.
The D3200’s mixer control data is transmitted on MIDI
channels 1–16. Set your external MIDI sequencer so that
it will record all sixteen MIDI channels. (For details, refer
to the manual of your MIDI sequencer.)
The D3200’s mixer control data is transmitted on MIDI
channels 1–16. Set your external MIDI sequencer so that
it will record all sixteen MIDI channels. (For details, refer
to the manual of your MIDI sequencer.)
For details on the parameters, refer to the MIDI implementa-
tion. Consult your local Korg distributor for more informa-
tion on MIDI Implementation.
tion. Consult your local Korg distributor for more informa-
tion on MIDI Implementation.
(5) Begin recording.
Press the D3200’s PLAY key to begin playback, and the
external MIDI sequencer will begin synchronized
recording. Now if you operate the mixer parameters
(faders, pan, EQ etc.), the corresponding control change
messages will be transmitted from the D3200 and will be
recorded on the external MIDI sequencer.
external MIDI sequencer will begin synchronized
recording. Now if you operate the mixer parameters
(faders, pan, EQ etc.), the corresponding control change
messages will be transmitted from the D3200 and will be
recorded on the external MIDI sequencer.
(6) Stop the D3200.
When you press the D3200’s STOP key to stop playback,
the external MIDI device will also stop recording. The
D3200’s mixer parameter operations have now been
recorded on the external MIDI device.
the external MIDI device will also stop recording. The
D3200’s mixer parameter operations have now been
recorded on the external MIDI device.
Receiving the mixer operations recorded above in “i.e.
Recording D3200 mixer operations ...” from your exter-
nal MIDI sequencer to control the D3200 mixer
Recording D3200 mixer operations ...” from your exter-
nal MIDI sequencer to control the D3200 mixer
(1) Use a MIDI cable to connect the two devices.
Use MIDI cables to connect the MIDI IN connectors and
MIDI OUT connectors of the D3200 and your MIDI
sequencer to each other.
MIDI OUT connectors of the D3200 and your MIDI
sequencer to each other.
(2) Adjust the synchronization settings on the D3200 and
on your external MIDI sequencer.
Access the SYSTEM/MIDI, “MIDI/MMC” tab page,
and set “MIDI Sync” to “MTC Master.”
Set your external MIDI sequencer to function as MTC
Slave. (For details, refer to the manual of your MIDI
sequencer.)
Access the SYSTEM/MIDI, “MIDI/MMC” tab page,
and set “MIDI Sync” to “MTC Master.”
Set your external MIDI sequencer to function as MTC
Slave. (For details, refer to the manual of your MIDI
sequencer.)
(3) Enable control change reception on the D3200.
• In the SYSTEM/MIDI, “MIDI/MMC” tab page, turn
the “MIDI” parameter “Control Change” to turn it
on.
on.
• In the SCENE, “Automation” tab page, click “Auto-
mation”
to turn it off.
(4) Press the D3200’s PLAY key.
When the D3200 starts playing, your external MIDI
sequencer will also begin playing in synchronization.
The previously-recorded mixer operation data will be
transmitted from the MIDI sequencer, causing the set-
tings of the D3200’s mixer to change.
sequencer will also begin playing in synchronization.
The previously-recorded mixer operation data will be
transmitted from the MIDI sequencer, causing the set-
tings of the D3200’s mixer to change.