Char-Broil 463243812 Manuale Utente

• Remove cooking grates and flame tamers. Light burners, rotate 

knobs from HI to LOW. You should see a smaller flame in 
LOW position than seen on HI. Perform burner flame check 
on sideburner, also. Always check flame prior to each use. If 
only low flame is seen refer to "Sudden drop or low flame" in 
the Troubleshooting Section.

s

1. Open lid. Turn ON gas at LP cylinder. 

3. Push in and turn far right or far left burner knob to the HI

burner lights and stays lit.

4. Light adjacent burners in sequence by pushing knobs in and 

turning to the HI position.

• Turn all knobs to the OFFposition. Turn LP cylinder OFF by turning 

hand-wheel clockwise to a full stop.

• Turn gas off at LP cylinder. Press and hold electronic ignitor 

button.  "Click" should be heard and spark seen each time 
between each collector box or burner and electrode. See 
"Troubleshooting" if no click or spark.

checking valves.  Knobs lock in  

position. To check 

valves, first push in knobs and release, knobs should spring 
back. If knobs do not spring back, replace valve assembly 
before using grill. Turn knobs to LOW position then turn back to  

position. Valves should turn smoothly.  

• Before each use, check to see if hoses are cut or worn or kinked. 

Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified by manufacturer.

• Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory (and should never be painted). Apply a strong solution 
of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. Do not apply a caustic grill/oven cleaner to painted 
surfaces. 

• Plastic parts: Wash with warm soapy water and wipe dry.

s

 Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

• Porcelain surfaces: Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner. Use nonabrasive scouring powder 
for stubborn stains.

• Painted surfaces: Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

• Stainless steel surfaces: To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

OFF  

OFF  

s

  Do not lean over grill while lighting.

1. Open sideburner lid. Turn ON gas at LP cylinder.
2. Turn sideburner knob to the HI position, push and hold

ELECTRONIC IGNITOR button.

3. If sideburner does NOT light within 5 seconds, turn knob to OFF, 

wait 5 minutes, then 

1. Open sideburner lid. Turn ON

2. Place lit match near burner.
3. Turn sideburner knob to the

Be sure burner lights and
stays lit.

2. Place match into match holder (hanging from side panel of 

grill). Light match; then light burner by placing match through 
the match light hole on right or left side of grill.

HI position.

8. For grills equipped with ELECTRONIC IGNITION at

Repeat steps 4 through 6 to light each burner.

9. Once each burner has ignited, turn knobs to desired setting.

gas at LP cylinder.

repeat lighting procedure.

position, depending on match light hole selected. Be sure

8