Marvel 8SWCEL Istruzione Sull'Installazione

Figure 6 “Single Zone”

Glass and Solid Door Models

Status 

LED

6

ON OFF   Door Ajar       

         Power Failure                       

Hi / Low Temp Upper             

Hi / Low Temp Lower

Figure 7 “Dual Zone”

Glass Door Models

Status

message

Only on glass door models

Your product will start upon plug-in to power receptacle.  The 

Sentry System LED will be flashing “amber” on single-zone mod-

els, (Figure 6), or displaying “power failure” on dual-zone mod-

els, , (Figure 7), to indicate that a power outage has occurred.  

This is normal as the product was powered-up at the factory for 

quality assurance testing.  Momentarily press and release the 

“ON/OFF” keypad to reset the control alarm status.  The LED 

should indicate steady green (single zone) no alarms (dual zone). 

To turn the unit ON/OFF, press and hold the “ON/OFF” key for a 

minimum of 5 seconds.

Your control is factory set to display temperature in ºFahrenheit 

as indicated by ºF in the upper right corner of the temperature 

display.  If this is the desired temperature units, no action is 

required.  If you prefer to display temperature in ºCelsius, mo-

mentarily press the “ºF/ºC” keypad.  ºC should now be displayed 

in the upper right corner of the temperature display.  You may 

“toggle” between ºF or ºC temperature display at any time by 

momentarily pressing the “ºF/ºC” keypad.

Your control is factory set to 55ºF.  This is the ideal long-term 

storage temperature for “both” red and white wines.  The stor-

age compartment temperature can be adjusted throughout the 

full range of red and white wine serving temperatures, (40ºF > 

65ºF).

To set the storage compartment temperature, momentarily 

press the “Set” keypad.  The display will now change to 

show the current set-point temperature, and “SET” will be 

displayed to indicate that you are in temperature set mode.  

While in SET mode you may press the “Warmer” or “Colder” 

keypads to adjust the set-point to your desired temperature 

in 1º increments. When your desired temperature is dis-

played, you may exit SET mode by momentarily pressing the 

“Set” keypad, or SET mode will time-out after 10 seconds of 

inactivity.

The control allows independent temperature control for 

both the upper and lower storage compartments.  On Dual 

Zone models, momentarily pressing  the “Set” keypad will 

select each compartment individually as indicated by SET 

being displayed in the “Upper” or “Lower” compartment 

temperature display.  While SET is displayed, you may press 

the “Warmer” or “Colder” keypads to adjust the storage 

compartment set-point to your desired temperature.  To exit 

SET mode, momentarily press the “Set” keypad until SET is 

no longer displayed in either the Upper or Lower displays, or 

SET mode will time-out after 10 seconds of inactivity. 

Compartment temperatures will be controlled to the tem-

perature displayed when SET mode is exited.

Important: it is suggested to allow 24 hours after changing 

the storage compartment set-point temperatures before 

making further adjustments.  This will allow the content 

temperatures to stabilize at the new set-point tempera-

ture.  Frequent door openings may prolong this stabilization 

period.

A door activated interior compartment light is provided for your 

convenience.  On glass door models only, this light may also be 

used to enhance the display of your wines through the glass 

door.  To activate the display lighting mode on glass door models, 

momentarily press the “Light” keypad, (Figure 6 & 7).  When ac-

tivated, the interior light will remain on when the door is closed.  

Important: Use the display lighting option only when needed.  

The interior light generates heat which will increase the energy 

consumption of your product.

Power Failure-Flashing Amber

High/Low Temp-Red

Press ON/OFF-Reset

Alarms OFF-Steady Amber