Bosch d9412gv3 Manuale Utente
D9412GV3/D7412GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters
EN | 19
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
There are four Route Groups which contain a
selection of event categorizes and individual events.
Each group has a primary and a backup device. The
primary device is the first (most important) destination
used to reach the programmed route within this
group. The backup device is used if the primary
device fails.
selection of event categorizes and individual events.
Each group has a primary and a backup device. The
primary device is the first (most important) destination
used to reach the programmed route within this
group. The backup device is used if the primary
device fails.
R# Primary Device
Default:
No Device
Selection:
No Device, Phone 1..4, SDI ##
Path 1..4
Path 1..4
Phone 1
Phone 1 is this group’s primary
destination.
destination.
Phone 2
Phone 2 is this group’s primary
destination.
destination.
Phone 3
Phone 3 is this group’s primary
destination.
destination.
Phone 4
Phone 4 is this group’s primary
destination.
destination.
SDI 88 Path 1
Path 1 on SDI 88 is this group's
primary destination.
primary destination.
SDI 88 Path 2
Path 2 on SDI 88 is this group's
primary destination.
primary destination.
SDI 88 Path 3
Path 3 on SDI 88 is this group's
primary destination.
primary destination.
SDI 88 Path 4
Path 4 on SDI 88 is this group's
primary destination.
primary destination.
SDI 92 Path 1
Path 1 on SDI 92 is this group's
primary destination.
primary destination.
SDI 92 Path 2
Path 2 on SDI 92 is this group's
primary destination.
primary destination.
SDI 92 Path 3
Path 3 on SDI 92 is this group's
primary destination.
primary destination.
SDI 92 Path 4
Path 4 on SDI 92 is this group's
primary destination.
primary destination.
To meet UL 864 requirements for
Central Station and Remote Station
applications, program a Primary
Device.
Central Station and Remote Station
applications, program a Primary
Device.
Select the communication device and the primary
destination.
Refer to Section 5.5
destination.
Refer to Section 5.5
Programming Path Numbers
and IP Addresses for Enhanced Communications on
page on page 131 to enable enhanced
communication paths.
page on page 131 to enable enhanced
communication paths.
Keypad Programming of R# Primary Device
D1255
1. Refer to Figure 1 on page 7 to access Keypad
1. Refer to Figure 1 on page 7 to access Keypad
Programming and navigate to the
ROUTE GRP 1 - 4 option.
ROUTE GRP 1 - 4 option.
2. At the ROUTE GRP 1 - 4 prompt, enter the route
group number you wish to configure and press
[ENT]. The keypad reads RT GRP 1 PRIMARY,
and then the current configuration (for example,
SDI 88 PATH 4).
[ENT]. The keypad reads RT GRP 1 PRIMARY,
and then the current configuration (for example,
SDI 88 PATH 4).
3. To change the configuration, press [ENT] when
the current configuration shows, and then press
[NEXT] or [PREV] to scroll through the options, as
listed in R# Primary Device on page 19.
[NEXT] or [PREV] to scroll through the options, as
listed in R# Primary Device on page 19.
4. When the keypad reads the desired configuration
option, press [ENT] to select it.
When the keypad reads PARAMETER SAVED,
your selection has been configured.
When the keypad reads PARAMETER SAVED,
your selection has been configured.
D1260
1. Refer to Figure 2 on page 8 to access Keypad
1. Refer to Figure 2 on page 8 to access Keypad
Programming and navigate to the
Route Group 1 - 4 option.
Route Group 1 - 4 option.
2. At the Route Group 1 - 4 prompt, enter the route
group number you wish to configure and press
[ENTER]. The keypad reads Rt Group 1 Primary,
and then the current configuration (for example,
SDI 88 PATH 4).
[ENTER]. The keypad reads Rt Group 1 Primary,
and then the current configuration (for example,
SDI 88 PATH 4).
3. To change the configuration, press the Edit
softkey, and then press the Next or the Previous
softkey to scroll through the options, as listed in
R# Primary Device on page 19.
softkey to scroll through the options, as listed in
R# Primary Device on page 19.
4. When the keypad reads the desired configuration
option, press the Save softkey to select it.
When the keypad reads Parameter Saved, your
selection has been configured.
selection has been configured.