Philips 3164965063 Manuale Utente

Prepare Rear Wall

Attach Mounting Plate to Wall

Prepare Top Cabinet

Adjust Blower

Mount the Microwave Oven

Make sure the screws for the 
blower motor and blower plate 
are securely tightened when 
they are reinstalled. This will 
help to prevent excessive 
vibration.

been properly routed and secured, 
and that the wires are not pinched.

Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.

Back of 
Microwave

You need to cut an opening in the rear wall for
outside exhaust.

Read the instructions on the REAR 
WALL TEMPLATE.

Tape it to the rear wall. 

Cut the opening, following the instructions of the
REAR WALL TEMPLATE.

Blower Plate

Remove Blower Plate

NOTE: IT IS VE

RY IMPOR

TANT TO

READ AND

 FOLLOW TH

E DIRECTIONS

IN THE IN

STALLATIO

N INSTRUCTIO

NS

BEFORE PR

OCEEDING

 WITH THIS

REAR WALL

 TEMPLATE

.

This Rear Wall 

Template serv

es to position 

the bottom 

mounting plate a

nd to locate the

 horizontal exhaust

 

outlet. 

1. Use a level 

to check that th

e template is posi

tioned 

    accurat

ely. 

2. Locate and 

mark at least one

 stud on the lef

t or 

    right side 

of the centerline.

It is 

important to use 

at least one woo

d 

screw mounted 

firmly in a stud

 to support the

 weight 

of the microw

ave. Mark two 

additional, evenly 

spaced 

locations for the 

supplied toggle 

bolts. 

3. Drill holes 

in the marked 

locations. Wh

ere there is 

    a stud, drill a 

3/16" hole for wood

 screws. For hol

es 

    that do not li

ne up with a stu

d, drill 5/8" hole

s for 

    toggle bolts. 

DO

 NOT INSTALL

 THE MOUNT

ING PLATE

AT THIS TIME.

 

4. Remove the

 template from

 the rear wall.

 

5. Review 

the Installation 

Instruction boo

k for your 

    installation sit

uation. 

Locate and

 mark holes to

 align with ho

les in the

 

mounting p

late. 

IMPORTANT:

 

LOCATE

 AT LEAST ON

E STUD ON EITH

ER SIDE OF 

THE CENTER

LINE. 

MARK TH

E LOCATION FOR

 2 ADDITIONAL

, EVENLY 

SPACED TOGG

LE BOLTS IN

 THE MOU

NTING PLA

TE

AREA.

Locate and

 mark holes to

 align with h

oles in the

 

mounting plate

. 

IMPORTA

NT: 

LOCATE

 AT LEAST ON

E STUD ON EIT

HER SIDE

 OF 

THE CENTER

LINE. 

MARK TH

E LOCAT

ION FOR

 2 ADDITIONAL

, EVENLY 

SPACED TOGG

LE BOLTS

 IN THE MOU

NTING PLA

TE

AREA.

Make sure the motor wiring has 

EN-16

NOTE: IT IS VERY I

MPORTANT TO

READ AND FOLLO

W THE DIRECTION

S

IN THE INSTALLAT

ION INSTRUCTION

S

BEFORE PROCEEDING

WITH THIS

REAR WALL TEMPLA

TE.

This Rear Wall Templ

ate serves to position th

e bottom

mounting plate and to l

ocate the horizontal ex

haust

outlet.
1. Use a level to chec

k that the template is p

ositioned

    accurately.
2. Locate and mark at le

ast one stud on the le

ft or

    right side of the cen

terline.

016'It is important to u

se at least one wood

screw mounted firmly i

n a stud to support the weigh

t

of the microwave. Mar

k two additional, evenly

spaced

locations for the suppl

ied toggle bolts.

3. Drill holes in the mar

ked locations. Where t

here is

    a stud, drill a 3/16" h

ole for wood screws. F

or holes

    that do not line up w

ith a stud, drill 5/8" ho

les for

    toggle bolts.
016'DO NOT INSTA

LL THE MOUNTING P

LATE

AT THIS TIME.
4. Remove the templa

te from the rear wall.

5. Review the Installation

Instruction book for you

r

    installation situation.

Locate and mark holes

 to align with holes i

n the

mounting plate.
IMPORTANT:
LOCATE AT LEAST

 ONE STUD ON EIT

HER SIDE OF

THE CENTERLINE.
MARK THE LOCATIO

N FOR 2 ADDITION

AL, EVENLY

SPACED TOGGLE BO

LTS IN THE MOUN

TING PLATE

AREA.

Locate and mark hol

es to align with holes

 in the

mounting plate.
IMPORTANT:
LOCATE AT LEAST ON

E STUD ON EITHER SI

DE OF

THE CENTERLINE.
MARK THE LOCATIO

N FOR 2 ADDITION

AL, EVENLY

SPACED TOGGLE BO

LTS IN THE MOUN

TING PLATE

AREA.