VTech 6053 プリント

NOTE: Use only the power adapters (or equivalent) 

supplied with your VTech telephone.

For complete feature instructions, please see 

the user’s manual.

96-006335-010-100   

issue 0

Plug the connector into the power jack at the bottom 

of the telephone base and chargers, then plug the 

power adapter into an electrical outlet not controlled 

by a wall switch.
Plug one end of the telephone line cord into the 

telephone line jack at the bottom of the telephone 

base. Then plug the other end of the cord into the 

modular wall telephone outlet.

•

•

•  Remove battery compartment cover by pressing on 

the indentation and sliding downwards. 

•  Align the two holes in the plug with the socket pins 

according  to  the  color-coded  label  in  the  battery 

compartment, then snap the plug into place. 

•  Place the battery into the compartment.  
•  Position the battery compartment cover and slide it 

upwards until it clicks into place.

•  Put the handset in the telephone base or the charger 

to charge the new battery for at least 16 hours.
The 

CHARGE light on the telephone base or 

charger will be on when the handset is properly 

positioned. Refer to the 

Troubleshooting section 

in the user’s manual if the 

CHARGE light is not on.

•

The 

ANS ON/OFF must be on (the button light will 

be on) in order for the machine to answer calls and 

record messages. If the button light is off then calls 

will not be answered. 
To turn on/off the answering system, press  

ANS ON/OFF to choose between on and off.    
Use the volume control button on the telephone base 

to  adjust  the  volume  at  anytime  during  the  setup 

procedure.

An outgoing announcement is the message callers hear 

when calls are answered by the answering system. 

The  telephone  is  preset  with  an  announcement  that 

answers calls with 

the tone.” You can use this default announcement, or 

replace it with your own.

To record your own announcement:
•  Press 

ANNC while in idle mode, and the system says  

again to record a new announcement.”  

•  Press 

ANNC  again  and  the  system  announces 

“

done.”

•  After the tone, speak towards the microphone at the 

bottom front of the telephone base from about nine 

inches away.

•  Press  /

PLAY/STOP when finished.    

•  The answering system will automatically playback the 

newly recorded announcement. Press  /

PLAY/STOP 

to stop the playback at any time.

If your product is not working properly:

Refer to the 

Troubleshooting section of the user’s 

manual.
Visit our website at www.vtechphones.com; in 

Canada, www.vtechcanada.com
Call our customer service at 1 (800) 595-9511; in 

Canada, 1 (800) 267-7377.

•

•

•

•   Press 

/

FLASH or 

 to ensure there is a dial 

tone, then dial the telephone number. 

 

 
  -OR-

To predial (view number before dialing): 
•  Dial the number (press 

MUTE/REMOVE to make 

corrections, or press and hold 

REDIAL/PAUSE to 

insert a dialing pause).
Press 

/

FLASH or   to use the speakerphone. 

•

•  Press 

/

FLASH  or 

  to  answer  an  incoming 

call.

•  Press 

OFF/CLEAR or put the handset back in the 

telephone base or charger.

color-coded label

The  telephone  base  settings  (ringer  melody, 

ringer  volume,  change  remote  access  code, 

clear  voicemail  and  reset  to  default  settings) 

can be changed using the handset, please see 

the user’s manual for complete instructions.