Honeywell M9481 ユーザーズマニュアル

AUXILIARY SWITCH RATINGS (amperes):

 has 1 spdt switch.

 has 2 spdt switches.

Full Load 7.2 3.6

Locked Rotor 43.2 21.6

 VA pilot duty, 1201240 

 on opposite contact.

DIMENSIONS: See Fig. 1.

UNDERWRITERS LABORATORIES INC. LISTED

File No. E4436; Guide No. XAPX.

CANADIAN STANDARDS ASSOCIATION CERTIFIED:

General Listing File No. 

15

30 

75

150

30

1 min 150

300

1.2 min   

 

  300 134.01   600 168.01

 torque is the maximum torque available to

overcome occasional large loads such as a seized

damper or valve. MOTOR MUST NOT BE USED

CONTINUOUSLY AT THIS RATING.

 of 

 min motor will damage motor.

ACCESSORIES:

ES6501 17 Explosion-proof Housing-Encloses motor

for use in explosive atmospheres. Not for use with

 Q618, and 

 Linkages. Order from Nel-

son Electric Co. Requires Honeywell 

 Cou-

pling.

Q607 External Auxiliary Switch-Controls auxiliary

equipment as a function of motor position.

Q605 Damper Linkage-Connects motor to damper.

INCLUDES MOTOR CRANK ARM.

0618 Linkage-Connects Modutrol motor to water or

steam valve.

Q601 Bracket and Linkage Assembly-Connects

Modutrol motor to water or steam valve.

 

 Linkage-Connects Modutrol motor to 

terfly valve. Requires adapter bracket packed with

motor.

 Potentiometer-Limits minimum position of

motor.

Q68 Dual Control Potentiometer-Controls 1 through 9

additional motors.

Q181 Auxiliary Potentiometer-Controls 1 or 2 addi-

tional motors.

 Motor Crank Arm-Infinitely adjustable crank

arm. Approximately 0.75 inches shorter than the

4074ELY crank arm, can rotate through downward
position and clear base of motor without requiring

use of adapter bracket.

220741A Screw Terminal Adapter-converts the stan-

dard quick-connect terminals to screws terminals.

Transformers-mounted internally, provide 24 

power to motor

 

 

 Hz (for electrical iso-

lation).

 

 

 Hz.

 

 

 Hz.

   

 Hz.

 Module with selectable voltage

ranges (4-7 Vdc, 6-9 Vdc, and 10.5-13.5 Vdc).

Adapts motor to M71 XX function.

 Module, selectable voltage or cur-

rent control, with adjustable null and span. Adapts
motor to 

 function; 4 to 20 

 or 2 to 10 Vdc.

 Module, for W936 economizer ap-

plications. Adapts motor to 

 function.

 Module, 3-wire 14-17 Vdc control

with minimum position capability. Adapts motor to

 function.

 up to 6 

 motors in unison

from one Series 90 controller.

 2 or 3 

 XX motors from a W973

Single-zone Logic Panel or 

 Discharge Air

Controller.

 one 

 motor from a 4-20 

Controller.

 up to 4 

 XX motors from a 4-20

 Controller.

 Resistor Board-Plugs onto quick-connects

in wiring box of 

 motor. Can be used in place

of 

 EAU, EDC, or EED resistor kits (func-

tions described above).

7616ADW Motor Crank Arm-Approximately 0.75

inches shorter than the 7616BR crank arm, can
rotate through the downward position and clear

base of motor without requiring use of adapter
bracket.

them could damage the product or cause a hazardous

condition.

2.

 ratings given in the instructions 

 the

product to make sure the product is suitable for your
application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

WHEN INSTALLING THIS PRODUCT...

1. Read these instructions carefully. Failure to follow

1.

2.

3.

operation as provided in these instructions.

Disconnect power supply before beginning 

stallation to prevent 

 shock and equip-

ment damage.
Never turn the motor shaft by hand or with a

wrench-this will damage the motor.

Always conduct a thorough checkout when in-
stallation is complete.

3 63-2195-l