Regency C33-NG3 ユーザーズマニュアル

16

Regency

®

 CLASSIC C33-3 Freestanding Gas Stove

1)  Turn burner OFF using "ON/OFF" switch.

2)  Turn gas control knob so indicator points 

to "OFF" position and allow 5 minutes for 
any gas in the combustion chamber to 
escape.

3) Turn gas control knob counterclockwise 

so indicator points to the "PILOT" position. 
Depress the gas control knob fully. Depress 
the igniter button several times until the 
pilot lights. After approximately one minute, 
release the gas control knob. The pilot fl ame 
should continue to burn. If the pilot does not 
remain lit, repeat operation allowing a longer 
period before releasing gas control knob.

4)  When the pilot stays lit, turn the gas knob 

further counterclockwise to the "ON" posi-
tion.

5)  Use the ON/OFF switch, wall switch, thermo-

stat or remote control to turn on the unit.

6)  Rotate the fl ame height regulator (Hi/Lo) to 

adjust the fl ame height higher or lower.

1)  Use the "ON/OFF" switch, wall switch, 

thermostat or remote control to turn off the 
burner.

2)  Push in the PILOT knob slightly and turn 

clockwise to "OFF". Do not force.

3)  Turn off all electric power to the appliance 

if service is to be performed. 

1) The 

FIRST FIRE in your stove is part of the 

paint curing process. To ensure that the paint 

is properly cured, it is recommended that 

you burn your fi replace for at least four (4) 

hours the fi rst time you use it with the fan 

on. When fi rst operated, the unit will release 

an odour caused by the curing of the paint 

and the burning off of any oils remaining 

from manufacturing. Smoke detectors in 

the house may go off at this time. Open 

a few windows to ventilate the room for a 

couple of hours. The glass panel may require 

cleaning.

2)  Read and understand these instructions 

before operating this appliance. 

3)  Check to see that all wiring is correct and 

enclosed to prevent possible shock.

4)  Check to ensure there are no gas leaks.

5)  Make sure the glass in the door frame is 

properly positioned. Never operate the ap-
pliance with the glass removed.

6)  Verify that the venting is unobstructed.

7)  Verify log placement. If the pilot cannot be 

seen when lighting the unit - the logs have 
been incorrectly positioned.

8)  The unit should never be turned off, and on 

again without a minimum of a 60 second 
wait for purging.

1)  Always turn off the gas valve before cleaning. 

For relighting, refer to lighting instructions. 
Keep the burner and control compartment 
clean by brushing and vacuuming at least 
once a year.

 

When cleaning the logs, use a soft clean 
brush as the logs are fragile and easily 
damaged.

2)  Clean appliance and door with a damp 

cloth (never when unit is hot).  Never use 
an abrasive cleaner. The glass should be 
cleaned with a gas fi replace glass cleaner 
(when it starts to cloud up). 

 
3)  The heater is fi nished in a heat resistant 

paint and should only be refi nished with 
heat resistant paint. Regency

®

 uses Stove 

Brite Paint - Metallic Black #6309.

4)  Make a  periodic check of burner for proper 

position and condition. Visually check the 
fl ame of the burner periodically, making sure 
the fl ames are steady; not lifting or fl oating. 
If there is a problem, call a qualifi ed service 
person. 

5)  The appliance and venting system must be 

inspected before use, and at least annually, 
by a qualifi ed fi eld service person, to ensure 
that the fl ow of combustion and ventilation 
air is not obstructed. 

 

During the annual service call, the burners 
should be removed from the burner tray 
and cleaned. Replace the embers and rock 
wool.

6)  Each time the appliance is lit, it may cause 

condensation and fog the glass.  This con-
densation is normal and will disappear in 
a few minutes as the glass heats up.

7)  Caution: Label all wires prior to discon-

nection when servicing controls. Wiring 
errors can cause improper and dangerous 
operation.  Verify proper operation after 
servicing.