Regency F39-LPG ユーザーズマニュアル
22
Regency
®
F39 Room Sealed Freestanding Gas Stove
ADJUSTING FLAME
HEIGHT
Your heater has an adjustable fl ame to tailor
the look and heat output to your specifi c needs.
It is adjusted by turning the fl ame adjustment
dial on the gas control valve.
Turn clockwise to adjust the fl ame higher,
counterclockwise for a lower fl ame.
counterclockwise for a lower fl ame.
OPERATING INSTRUCTIONS
AUTOMATIC
CONVECTION
FAN OPERATION
Set the fan speed on control panel at the top
rear of the unit to adjust to the desired speed.
The fan will turn on as the stove comes up
to operating temperature. After the unit has
been turned off and the unit cooled to below
a useful heat output range the fan will shut off
automatically.
rear of the unit to adjust to the desired speed.
The fan will turn on as the stove comes up
to operating temperature. After the unit has
been turned off and the unit cooled to below
a useful heat output range the fan will shut off
automatically.
OPERATING
INSTRUCTIONS
Before operating this appliance, proceed through
the following check list.
the following check list.
1) Read and understand these Instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) Make sure the three pieces of door glass
are properly positioned. Never operate the
appliance with any of the glass removed or
with the door open.
appliance with any of the glass removed or
with the door open.
5) Verify that all fl uing and the cap is unob-
structed.
6) Verify log placement. If the pilot cannot be
seen when lighting the unit - the logs or the
embers have been incorrectly positioned.
embers have been incorrectly positioned.
7) The unit should never to turned off and on
without a minimum of a 60 second wait.
LIGHTING
INSTRUCTIONS
IMPORTANT: The PILOT knob cannot be
turned from pilot to off unless it is partially
depressed.
turned from pilot to off unless it is partially
depressed.
Note: Open the pedestal door of the unit
before lighting the pilot. Once the
pilot is lit, close the door. You should
never operate the unit with the door
open.
pilot is lit, close the door. You should
never operate the unit with the door
open.
1) If the PILOT knob is in the off position
proceed to Step 4.
2) Push in PILOT knob slightly and turn clock-
wise to off. Knob cannot be turned from pilot
to off unless knob is pushed in slightly. Do
not force.
During the fi rst few fi res, a white fi lm
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the fi lm will bake on and
become very diffi cult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the fi lm will bake on and
become very diffi cult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
4) Turn the PILOT knob counterclockwise to
pilot and align it with the arrow as shown
in diagram above.
5) Push in PILOT knob all the way in and hold.
Immediately push IGNITOR button until pilot
lights. Continue to hold the PILOT knob in
for approximately one minute, then release
the PILOT knob. The pilot fl ame should
continue to burn. If the pilot does not remain
lit, repeat operation allowing a longer period
before releasing PILOT knob.
6) Turn PILOT knob counter clockwise to on.
7) Use the Burner ON/OFF switch to turn on
the burner.
8) Rotate the HEAT control to adjust the fl ame
height higher or lower.
SHUTDOWN
INSTRUCTIONS
1) Use the Burner ON/OFF switch, thermostat
or remote control to turn off the burner.
2) Push in the PILOT knob slightly and turn
clockwise to off. Do not force.
3) Turn off all electric power to the appliance if
service is to be performed.
FIRST FIRE
The FIRST FIRE in your stove is part of the
paint curing process. To ensure that the paint is
properly cured, it is recommended that you burn
your fi replace for at least four (4) hours the fi rst
time you use it with the fan on. When fi rst oper-
ated, the unit will release an odour caused by the
curing of the paint and the burning off of any oils
remaining from manufacturing. Smoke detectors
in the house may go off at this time. Open a few
windows to ventilate the room for a couple of
hours. The glass may require cleaning.
paint curing process. To ensure that the paint is
properly cured, it is recommended that you burn
your fi replace for at least four (4) hours the fi rst
time you use it with the fan on. When fi rst oper-
ated, the unit will release an odour caused by the
curing of the paint and the burning off of any oils
remaining from manufacturing. Smoke detectors
in the house may go off at this time. Open a few
windows to ventilate the room for a couple of
hours. The glass may require cleaning.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS STILL HOT!
GLASS WHILE IT IS STILL HOT!
Note: When the glass is cold and the appli-
ance is lit, it may cause condensation
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
WITHOUT THE GLASS FRONT IN
PLACE.
3) Wait fi ve minutes to allow gas, that may
have accumulated in the main burner
compartment, to escape. If you smell gas,
follow the instructions on the front of this
manual. If you don't smell gas continue on
to the next step.