Regency F38-LPG2 ユーザーズマニュアル

Regency F38-2 Freestanding Gas Stove

The clearances listed below are MINIMUM 
distances.  Measure the clearance to both the 
appliance and the chimney connector.  (The 
farthest distance is correct if the two clear-
ances do not coincide.) For example, if the 
appliance is set as indicated in one of the fi gures 
but the connector is too close, move the stove 
until the correct clearance to the connector is 
obtained.  

This unit can be installed on a solid combustible 
surface like a wood fl oor. This unit can also be 
installed directly on carpeting  or vinyl when 
the bottom pedestal cover plate (provided with 
unit) is installed.

This appliance may be installed only with the 
clearances as shown in the situations pictured.  
Do not combine clearances from one type of 
installation with another in order to achieve 
closer clearances. 

Use the minimum clearances shown in the 
diagrams below for all installations.

If further reduced clear-

ances are needed, ob-

tain requirements for 

construction of a pro-

tected wall from your 

local building authori-

ties and their allowable 

reductions of the listed 

clearances.

A  Side Wall to Unit 

7-1/2" / 190 mm

B  Back Wall to Unit 

6" / 155 mm

E  Side Wall to Unit 

2" / 50 mm

This heater has a draft diverter built in. It must 
not be altered, obstructed, or blocked in any way, 
and the unit must be installed so that the draft 
diverter is in the same atmospheric pressure 
zone as the combustion air inlet to the burner. 
This heater must be properly connected to a 
fl ueing system. This heater is equipped with a 
fl ue safety shutoff system.

WARNING: Operation of this heater when 
not connected to a properly installed and 
maintained fl ueing system or tampering with 
the fl ue safety shutoff system can result in 
carbon monoxide (CO) poisoning and pos-
sible death.

This heater is a fl ued appliance and must be 
connected to a chimney/fl ue in accordance with 
the installation codes.

For your safety this heater is equipped with a 
fl ue safety switch designed to sense incorrect 
fl ueing and react by shutting down the gas sup-
ply. This thermally actuated switch is located 
within the draft diverter and will detect either a 
blocked chimney or backdraft condition where the 
chimney fl ow has reversed. If this switch shuts 
the unit down, it indicates a drafting problem that 
must be identifi ed and rectifi ed without delay 
- the thermally activated switch must  never be 
bypassed or disconnected as a hazardous or 
deadly condition can result.

C  Back Wall to Flue Centerline 10-3/4" / 273 mm

D  Side Wall to Flue Centerline  20-1/2" / 520 mm

F  Side Wall to Flue Centerline  11" / 280 mm

14) This unit can be installed on a solid combus-

tible surface like a wood fl oor as well as on 
carpeting.

1)  Check Clearances to Combustibles. Refer to 

the "Clearance to Combustibles" section.

2)  Install flueing. Refer to the "Flueing" 

section.

3)  Make gas connections. Refer to the "Gas 

Connection" section. 

 

Test the pilot. Must be as per diagram in the 
"Pilot Adjustment" section. 

4)  If necessary, convert NG to LPG. Refer to 

the "Conversion from NG to LPG" section

5)  Test Gas Pressure. Refer to the "Gas Pipe 

Pressure Testing" section.

6)  Install log set. Refer to the "Log Set 

Installation" section.

7)  Install Front Door. Refer to the "Front Door 

Installation" section.

8) Test 

for 

fl ue spillage (draft test). Refer to the 

"Test for Flue Spillage" section.

9)  Install Optional Features. Refer to the 

following sections where applicable: 

 

a. Optional Wall Thermostat

 

b. Optional Remote Control

10) Final check. Refer to the "Final Check" 

section.

Before leaving this unit with the customer, the 
installer must ensure that the appliance is fi r-
ing correctly and operation fully explained to 
customer.

1)  Clocking the appliance to ensure the correct 

fi ring rate (rate noted on label) after burning 
appliance for 15 minutes.

2)  If required, adjusting the primary air to ensure 

that the fl ame does not carbon. First allow 
the unit to burn for 15-20 min. to stabilize.