Ei Electronics Ei146 プリント
Shannon Free Zone, Shannon, Co. Clare, Ireland.
Ph.
+353 61 471277
Fx.
+353 61 471053
Email.
eielectronics@eiltd.ie
Web:
www.eielectronics.com
E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior n otice
.
Ei146 DataSht RevB
Model
Ei146 Optical
Installation & Placement
Wiring for Interconnected Alarms
Be very careful about correctly wiring the alarms as mixing Live and Neutral
will blow/damage interconnected alarms.
Alarms should be placed in accordance with the general guidelines shown in
the diagram above. These recommendations are based on the problem of
areas of “dead air” close to corners of rooms and apexes of ceilings, which
could result in the prevention of smoke reaching the smoke detector
Please consult instruction booklet for specific installation details
will blow/damage interconnected alarms.
Alarms should be placed in accordance with the general guidelines shown in
the diagram above. These recommendations are based on the problem of
areas of “dead air” close to corners of rooms and apexes of ceilings, which
could result in the prevention of smoke reaching the smoke detector
Please consult instruction booklet for specific installation details
Important Precaution:
Do not install the actual smoke/heat alarm
itself in new or renovated buildings until all
work is completed (including floor coverings)
and the building has been fully cleaned. The
wiring can be installed when appropriate.
(Excessive dust and debris from building work
can contaminate the smoke chamber and
cause problems, and it will also invalidate the
guarantee). If it must be installed, cover it
completely, particularly around the edges, with
a dust cover (eg. a plastic bag), until all
cleaning is finished.. Connect wires to the unit
as in wiring diagram. All wiring must comply
with local codes.
itself in new or renovated buildings until all
work is completed (including floor coverings)
and the building has been fully cleaned. The
wiring can be installed when appropriate.
(Excessive dust and debris from building work
can contaminate the smoke chamber and
cause problems, and it will also invalidate the
guarantee). If it must be installed, cover it
completely, particularly around the edges, with
a dust cover (eg. a plastic bag), until all
cleaning is finished.. Connect wires to the unit
as in wiring diagram. All wiring must comply
with local codes.
Technical Specification
Sensor
Optical, uses light scatter from
smoke
smoke
Sensitivity:
Complies with BS 5446 Part 1:
2000
2000
Source:
Contains no radioactive material
Airspeed:
Essentially immune to the effect
of airspeed.
Button Test:
Simulates the effect of smoke and
checks chamber, electronics and
horn.
checks chamber, electronics and
horn.
Ambient Light:
Chamber housing design and
compensation overcomes
problems with stray light.
compensation overcomes
problems with stray light.
AutomaticSelf-Test:
Smoke Chamber is tested every 40
Sec. and unit beeps (without LED
flash) if it is degraded.
Insect Screen:
Prevents insects or debris entering
chamber (1.00mm mesh size)
chamber (1.00mm mesh size)
Supply Voltage:
230V AC
Battery back up:
9V Alkaline Battery
Specifications are subject to change
Power-On Indicator:
Continuous green LED
Alarm:
Electronic Piezoelectric horn
Alarm Sound Output:
85dB (minimum) at 3m
Alarm Status:
Red LED flashes every second on
unit sensing fire
Temperature Range:
0° to 40°C
Humidity Range:
15% to 95% Relative Humidity
Interconnect:
Up to 12 interconnected mains
powered easi-fit smoke or heat
alarms, along with an EI128 relay
base
powered easi-fit smoke or heat
alarms, along with an EI128 relay
base
Fixing:
Easi-Fit mounting base
Plastic material:
UL94VO flame retardant
Dimensions:
152mm x 50mm depth
Weight:
345g
Warranty:
5 year (limited) warranty
Approvals:
Kitemarked to BS EN 14604:2005,
CE Approved
CE Approved