Denon AVR-4810CI ユーザーズマニュアル
Get
ting Star
ting Star
ted
Connections
Set
tin
g
tin
g
s
Pla
ybac
Pla
ybac
k
Remot
e Contr
ol
Multi-z
one
Inf
or
or
mation
Tr
oubleshooting
Specifications
Pla
ybac
ybac
k
Tuning in Radio Stations – XM Satellite Radio and SIRIUS Satellite Radio
The strength of both the SIRIUS satellite and terrestrial signals can be
checked “Antenna Aiming” (vpage 64).
checked “Antenna Aiming” (vpage 64).
Checking the SIRIUS Signal Strength and Radio ID
1
Press
<STATUS>
until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
reception conditions.
Display
Status
EXCELLENT
Signal strength is excellent
GOOD
Signal strength is good
WEAK
Signal strength is weak
NO SIGNAL
No signal
2
Adjust the position of the antenna until “SIGNAL:
EXCELLENT” is shown on the display.
3
Press
<STATUS>
until the channel (example:
“SR001”) is displayed.
4
Press
[TU
d
]
or
[TU
f
]
and select channel 0 (SR000).
Channel No. and Sirius ID are alternately shown on the display.
SR000 SiriusID
************
Write your own SIRIUS ID for storage use.
Sirius ID :
Sirius ID :
b
Sirius ID
The channel switches continuously when
[TU
d
]
or
[TU
f
]
is pressed
and held.
The song title, artist name, composer name, category and reception
level can be checked by pressing
The song title, artist name, composer name, category and reception
level can be checked by pressing
<STATUS>
.
The time (default : 30 sec) for which the GUI menu are displayed can
be set “GUI” – “Tuner” (vpage 54).
be set “GUI” – “Tuner” (vpage 54).
Press
uio
p
to return to
the original screen.
•
•
•
When operating SIRIUS with the AVR-4810CI via the main remote
control unit or sub remote control unit, use
control unit or sub remote control unit, use
[SAT TU]
.
Before operating, set to
[SAT TU]
operating mode.
[SAT TU]
of
[INPUT SOURCE SELECT]
and
[SAT TU]
of
[DEVICE
SELECT]
mode can use only either XM or SIRIUS. The default setting
is for SIRIUS operation.
1
Set GUI menu “Option Setup” – “Remote (SIRIUS/
XM)” (vpage 55) to “SAT TU : SIRIUS”.
2
Press
[SOURCE SELECT]
to display the GUI Source
Select menu, then select “
” (vpage 31).
The input source becomes that set in step 1.
3
Set the main remote control unit to the “SAT TU”
mode (vpage 108 “Operating the Main Remote
Control Unit”).
You can then operate the input source you set in step 1.
4
Use
[TU
d
]
or
[TU
f
]
to select the channel.
When the channel is tuned in, the name of the song and artist
are displayed.
are displayed.
5
Adjust the items below.
Adjusting the master volume
(vpage 85)
Selecting the surround mode
(vpage 87)
Adjusting the Sound and Picture Quality
(vpage 90)
n
n
n
n
n
Listening to SIRIUS Satellite Radio
Presetting Radio Channels (Preset Memory)
Your favorite broadcast channels can be preset so that you can tune
them in easily. Up to 56 channels can be preset.
them in easily. Up to 56 channels can be preset.
To preset other channels, repeat steps 1 to 4.
NOTE
Preset channels are erased by overwriting them.
Listening to Preset Channels
You can also operate via the main unit. In this case, perform the
following operations.
Press
following operations.
Press
<TUNING PRESET>
, then turn
<SOURCE SELECT>
to select the
preset radio channel.
Press
[CHANNEL]
to select the desired preset channel,
then press
ENTER
.
Selection is still possible if you press
[1
~
8]
after pressing
[A
~
G]
.
b
1
Tune in the broadcast channel you want to preset.
2
Press
[MEMO]
.
3
Press
[A ~ G]
to select the block in which the channel
is to be preset, then press
[CHANNEL]
or
[1 ~ 8]
to
select the preset number.
The memory block can also be selected by pressing
[SHIFT]
on
the sub remote control unit.
b
4
Press
[MEMO]
again to complete the setting.