Integra DTR-7.4 ユーザーズマニュアル
26
Connecting
-compatible AV Components
The
terminal on the DTR-7.4 is for connecting other
Integra/Onkyo components equipped with the same
terminal. When a component is connected to the
terminal, it can be operated by the remote controller
supplied with the DTR-7.4. In addition, when you
connect a component to the
supplied with the DTR-7.4. In addition, when you
connect a component to the
terminal, you can also
perform the system operations given below.
Power on/ready function
When the DTR-7.4 is in the standby state, if an
-
connected component is turned on, the DTR-7.4 also
turns on and the input source selected at the DTR-7.4
automatically switches to that component.
Be aware that this function will not work if the power cord for the
turns on and the input source selected at the DTR-7.4
automatically switches to that component.
Be aware that this function will not work if the power cord for the
-connected component is connected to the AC OUTLET on
the DTR-7.4, or if the DTR-7.4 has already been turned on.
Direct change function
When the play button is pressed on an
-connected
component, the input source selected at the DTR-7.4
automatically changes to that component.
automatically changes to that component.
Power off function
When the DTR-7.4 is placed in the standby state, all
-connected components are also automatically put
into the standby state.
Also, if you press the On button on the DTR-7.4 remote
controller while the DTR-7.4 is turned on, all
Also, if you press the On button on the DTR-7.4 remote
controller while the DTR-7.4 is turned on, all
-
connected components (DVD players, CD players, MD
recorders, tuners, etc.) are also turned on.
recorders, tuners, etc.) are also turned on.
To connect components using the
terminal, simply
connect a remote control cable from this
terminal to the
terminal of the other component. An
remote control
cable with a 1/8 inch (3.5 mm) miniature two-conductor plug
comes with every cassette tape deck, compact disc player,
MD recorder, and DVD player that has an
comes with every cassette tape deck, compact disc player,
MD recorder, and DVD player that has an
terminal.
• When performing operations with
-connected
components using the
system, do not use the
remote zone (Zone 2).
• For remote control operation, the audio connection
cables must also be connected.
• If a component has two
terminals, you can use
either one to connect to the DTR-7.4. The other one
can be used to daisy chain with another component.
can be used to daisy chain with another component.
• With Integra/Onkyo DVD players, you can enter the
pre-program code so that you can operate the DVD
player directly with the remote controller without
connecting the
player directly with the remote controller without
connecting the
terminals (See page 89).
Connections for Remote Control (
)
FM
75
75
OUT
OUT
OUT
OUT
L
PHONO
PRE OUT
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
AUDIO
VIDEO
S VIDEO
GND
SURR
BACK/
ZONE 2
R
L
IN
A
R
CENTER
ETHERNET
(Net -Tune)
(Net -Tune)
R
L
MULTI CH
INPUT
INPUT
FRONT
SUB
SURR
SURR
BACK
BACK
CENTER
R
L
ANTENNA
Y
P
B
P
R
OUTPUT
INPUT 1
Y
P
B
P
R
INPUT 2
Y
P
B
P
R
FRONT SPEAKERS
L
R
L
R
SURR SPEAKERS
CENTER
SPEAKER
SPEAKER
R
L
IN
ZONE 2
REMOTE
CONTROL
CONTROL
A
B
OUT
12 V
TRIGGER OUT
TRIGGER OUT
DIGITAL
IN
OPT
2
1
2
3
1
3
COAX
OPT
1
2
DIGITAL
OUT
COMPONENT
VIDEO
I R
RS232
AM
REMOTE
CONTROL
CONTROL
L
R
ANALOG
OUTPUT
DIGITAL OUT
COAX
AUDIO
R
L
IN
DIGITAL
IN
COAX
1
REMOTE
CONTROL
Integra/Onkyo DVD player
Remote
control
cable
control
cable
REMOTE
CONTROL
DTR-7.4
Ex: Integra/Onkyo CD
player
player
connector
connector
Ex: Onkyo cassette tape
deck
deck
Remote control cable