Integra DTR-7.4 ユーザーズマニュアル
89
Using the Remote Controller with Other
Components
Components
You can use the DTR-7.4’s remote controller (RC-
550M) to control your other AV components, including
those made by other manufacturers. To do this you can:
• Enter a remote control code for the component that
550M) to control your other AV components, including
those made by other manufacturers. To do this you can:
• Enter a remote control code for the component that
you want to control (e.g., DVD, TV, VCR).
• Learn commands directly from the other component’s
remote controller (see page 94).
• Use the Macro function to learn a sequence of actions
(see page 95).
• You can also edit the remote controller modes (see
page 97).
By entering the appropriate remote control code for
each of your components, you can control each compo-
nent by selecting the relevant remote controller mode:
DVD, TV, VCR, CBL (cable), or SAT (satellite).
each of your components, you can control each compo-
nent by selecting the relevant remote controller mode:
DVD, TV, VCR, CBL (cable), or SAT (satellite).
Remote Control Codes for an Onkyo DVD player
The remote control code that you use with an Onkyo
DVD player depends on whether it’s connected via
,
as follows:
5001: Use this code if you’ve connected an
cable
and an RCA/phono analog audio connection cable to
your DVD player. This is the default setting, so if
you’re using
your DVD player. This is the default setting, so if
you’re using
, you don’t need to change it. Point
the remote controller at the DTR-7.4 to operate the
DVD player.
5002: Use this code if your DVD player doesn’t have
an
DVD player.
5002: Use this code if your DVD player doesn’t have
an
socket, or you’re not using
. Point the
remote controller at the DVD player to operate it.
Entering a Remote Control Code
1
Look up the appropriate remote
control code for the component.
control code for the component.
See “Remote Control Codes” on page
90-91.
90-91.
2
Press and hold down the Custom
button for more than three sec-
onds.
button for more than three sec-
onds.
The remote controller enters Custom
mode.
mode.
3
Roll the scroll wheel to select
“PRGRM,” and then press the
scroll wheel.
“PRGRM,” and then press the
scroll wheel.
4
Roll the scroll wheel to select the
the remote controller mode you
want to use with the component,
and then press the scroll wheel.
the remote controller mode you
want to use with the component,
and then press the scroll wheel.
The following remote controller modes
can be selected: DVD, TV, VCR, CBL,
or SAT.
can be selected: DVD, TV, VCR, CBL,
or SAT.
Custom
5
Use the number buttons to enter
the 4-digit remote control code.
the 4-digit remote control code.
If the code is accepted, the following
appears on the display for a while, and
then the normal display reappears.
appears on the display for a while, and
then the normal display reappears.
If the code is not accepted, after the
message “RETRY” has been displayed,
the code entry display reappears, and
you should try entering the code again.
To cancel this procedure at any point,
press the Custom button.
message “RETRY” has been displayed,
the code entry display reappears, and
you should try entering the code again.
To cancel this procedure at any point,
press the Custom button.
6
Select the remote controller mode,
point the remote controller at the
component, and check its opera-
tion.
point the remote controller at the
component, and check its opera-
tion.
The remote controller buttons that can
be used in DVD mode are shown on
page 84. Those that can be used with the
TV, VCR, CBL, and SAT modes are
listed on pages 92 and 93.
be used in DVD mode are shown on
page 84. Those that can be used with the
TV, VCR, CBL, and SAT modes are
listed on pages 92 and 93.
Remote Contr
oller