Madrigal Imaging N380S ユーザーズマニュアル
14
4
RECORD OUTPUTS
Connect these outputs to the right-channel and left-channel tape inputs of
your recorder. Make a note of which set of
Connect these outputs to the right-channel and left-channel tape inputs of
your recorder. Make a note of which set of
record outputs
you used with
which recording device. It is important to name the inputs you use and to
associate the correct
associate the correct
record output
with the appropriate recording device.
By giving the Nº380S this information, it can prevent accidental record
loops that might otherwise create disturbing feedback. (See “programming
input names” and “assigning record outputs” on pages 20-21.)
loops that might otherwise create disturbing feedback. (See “programming
input names” and “assigning record outputs” on pages 20-21.)
These outputs are unaffected by the
output level
control on the front panel
of the Nº380S, or by the source chosen to be monitored.
5
SLAVE AND MASTER COMMUNICATOR PORTS
These communications ports allow the Nº380S to “link” to certain compat-
ible Mark Levinson components. (See “Linked Functions.”)
These communications ports allow the Nº380S to “link” to certain compat-
ible Mark Levinson components. (See “Linked Functions.”)
MADRIGAL AUDIO LABORATORIES
R
R E F E R E N C E
M O N A U R A L
A M P L I F I E R
M O N A U R A L
A M P L I F I E R
N º 3 3
MADRIGAL AUDIO LABORATORIES
R
R E F E R E N C E
M O N A U R A L
A M P L I F I E R
M O N A U R A L
A M P L I F I E R
N º 3 3
slave in
master
slave out
processor
slave
master
slave in
slave out
slave in
transport
preamp
power
amp(s)
8 to 8 Link Cable
8 to 8 Link Cable
6 to 6 Link Cable
8 to 6 Link Cable
The Mark Levinson Linking system uses a Digital Audio Processor as the
Master of (and central clearinghouse for) inter-component communications.
Other components such as digital transports are connected to the Master as
“Slaves,” and can be “daisy-chained” using their Slave In and Slave Out jacks.
As the ultimate destination of all source signals, the Nº380S Preamplifier
must be the final “Slave” in the chain. (In technical terms, it terminates the
communications bus.) In turn, the Nº380S can serve as a master to an asso-
ciated compatible Mark Levinson power amplifier—hence its “Master” com-
munications port.
Master of (and central clearinghouse for) inter-component communications.
Other components such as digital transports are connected to the Master as
“Slaves,” and can be “daisy-chained” using their Slave In and Slave Out jacks.
As the ultimate destination of all source signals, the Nº380S Preamplifier
must be the final “Slave” in the chain. (In technical terms, it terminates the
communications bus.) In turn, the Nº380S can serve as a master to an asso-
ciated compatible Mark Levinson power amplifier—hence its “Master” com-
munications port.
Thus, if the only other Mark Levinson Link-compatible component you
have is a digital audio processor, connect its
have is a digital audio processor, connect its
master
port to the Nº380S’
slave
port using a “straight-through” RJ-45 cable. If there are additional Mark
Levinson Link-compatible components in the system, place the Nº380S at
the end of the chain by connecting the last
the end of the chain by connecting the last
slave out
port to the Nº380S’
slave
port. See the diagram (left) for clarification.
The RJ-45 cable needed for the Link connection between source compo-
nents and the preamplifier may be purchased from your Mark Levinson
dealer. It may also be easily and inexpensively made to length using two
RJ-45 connectors and the appropriate length (up to 100 feet/30 meters) of
RJ-45 (flat, eight conductor) cable.
nents and the preamplifier may be purchased from your Mark Levinson
dealer. It may also be easily and inexpensively made to length using two
RJ-45 connectors and the appropriate length (up to 100 feet/30 meters) of
RJ-45 (flat, eight conductor) cable.
RJ-45 cables and connectors are used throughout the world for both tele-
communications and computers, and are widely available at low cost. The
connectors are crimped on to the ends of the cable such that pin 1 at one
end is connected to pin 1 at the other end. Such a “straight-through” con-
nection is (counter-intuitively) made by introducing a 180
communications and computers, and are widely available at low cost. The
connectors are crimped on to the ends of the cable such that pin 1 at one
end is connected to pin 1 at the other end. Such a “straight-through” con-
nection is (counter-intuitively) made by introducing a 180
°
twist in the
cable between the two ends, as shown below.
building a link cable
To Nº380S
To Mark Levinson
®
digital processor
Locking tab
Locking tab
180
°
twist
The power amplifier Link connection is made using a 6-conductor Link
cable. Connect the Nº380S’
cable. Connect the Nº380S’
master
port to the
slave
port of a compatible
Mark Levinson power amplifier.