Denon ADV-M51 ユーザーズマニュアル
ENGLISH
44
1
In the still mode, press one of the
6
/
7
buttons on the
remote control unit.
6
: Reverse direction
7
: Forward direction
• When pressed again, the slow play speed increases.
(Four step) (Three step on video CDs)
• Press the PLAY button to resume normal playback.
(9) Slow Playback (for DVDs and video CDs only)
7
6
Remote control unit
NOTE:
• Reverse slow play is not possible on video CDs.
BAND
PHONES
VOLUME
ON / STANDBY
DVD SURROUND RECEIVER ADV-M51
TONE / SDB
FUNCTION
MENU / SET
+
-
SURROUND / SELECT
PUSH - PARAM.
5
1 3
+
-
-
A / V
3
STATUS
SETUP
TONE /SDB
FUNCTION
SURROUND
INPUT MODE
TEST TONE
DVD
TUNER
CH
6
5
4
9
8
7
0
/10
CALL
ENTER
MUTING
+10
SYSTEM
MD
CDR TAPE
TUNER TV / VCR
SURROUND
AUTO DECODE
VIRTUAL
DIRECT
5CH STEREO
STEREO
IN/SURR.
IN/SURR.
DVD
9
8
2
1
7
6
+
-
5
2
3
1
12 OPERATING THE SURROUND FUNCTIONS
Input mode setting
1
Press the FUNCTION button to select the input function to be
played.
played.
FUNCTION
FUNCTION
• The function switches as shown below.
• Factory default (LINE 1) = MD, (LINE 2) = TAPE
• Factory default (LINE 1) = MD, (LINE 2) = TAPE
DVD
TUNER
(LINE2)
D.AUX
(LINE1)
Main unit
Remote control unit
2
When DVD, D.AUX or (LINE1) = MD was selected as the
input function, press the remote control unit’s INPUT MODE
button to select the input mode.
input function, press the remote control unit’s INPUT MODE
button to select the input mode.
INPUT MODE
• “ANALOG” cannot be selected when DVD or D.AUX was
selected as the input function.
• “ANALOG” can be selected when “LINE-2” is set to
“D.AUX” at “FUNCTION ASSIGNMENT” under “SYSTEM
SETUP” in the detailed settings.
SETUP” in the detailed settings.
AUTO
PCM
DTS
ANALOG
Remote control unit
Input mode selection function
• The input mode can be selected when the input function is
set to DVD, D.AUX or (LINE1) = MD.
• Different input modes can be selected for each input
function. The selected input mode is stored in the memory
for the individual input functions.
for the individual input functions.
• When the input function is set to something other than the
above, “ANALOG ONLY” is displayed and the input mode
cannot be selected.
cannot be selected.
q AUTO (auto mode)
In this mode, the type of signal being input to the digital
and analog input terminals is detected and the program in
the set’s surround decoder is switched automatically to
play the signals for the selected input function.
The presence or absence of digital signals is detected, the
signals input to the digital input are identified and decoding
and playback are performed automatically in DTS, Dolby
Digital or PCM (2 channel stereo) format.
If no digital signal (LINE1) = MD is being input, the analog
input jacks are selected.
Use this mode to play Dolby Digital signals.
and analog input terminals is detected and the program in
the set’s surround decoder is switched automatically to
play the signals for the selected input function.
The presence or absence of digital signals is detected, the
signals input to the digital input are identified and decoding
and playback are performed automatically in DTS, Dolby
Digital or PCM (2 channel stereo) format.
If no digital signal (LINE1) = MD is being input, the analog
input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM
signals are being input.
signals are being input.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS
signals are being input.
signals are being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are played.
(This cannot be selected in the DVD mode.)
(This cannot be selected in the DVD mode.)
The input mode automatically switches to “AUTO” if you
switch the input function to DVD from anything other than
DVD.
switch the input function to DVD from anything other than
DVD.