JVC GET0602-001A ユーザーズマニュアル
2
160
91.3
100
30˚
Dashboard
儀表盤
儀表盤
20
4
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used,
parts could become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note:
Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Do the required electrical connections.
• See pages 3 – 6.
4
Install this unit using the screws removed in step
1
.
The following example is for installation in a Toyota car. For more details, consult your JVC car audio
dealer.
dealer.
If necessary, restore the protruding tabs.
若有必要，請重新裝上凸緣。
若有必要，請重新裝上凸緣。
Supplied screws
配備螺絲
配備螺絲
Note :
When installing the unit on the mounting bracket, make sure to use the supplied screws
(M5 × 8 mm). If longer screws are used, they could damage the unit.
(M5 × 8 mm). If longer screws are used, they could damage the unit.
注意：
安裝本機進裝配架時，請務必使用配備的螺絲（M5 × 8 mm）。若使用比較長的螺絲，
有關螺絲可能會損壞本機。.
有關螺絲可能會損壞本機。.
安裝（裝設、固定在儀表板內）
下面的圖解表示了典型的安裝程序。但是在實際安裝時，您應該根據您的汽車作適當的調整。如果
您有問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
您有問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
安裝本機之前
• 當裝上本機時，必須按照指示使用配備的螺絲釘。如果使用其它的螺絲釘，相關零件可能會鬆
脫或損壞。
• 當鎖緊螺絲釘或螺栓時，切記不要壓擠到任何連接電線。
• 當安裝上後，切記不要阻擋到後面板的風扇以維持適當的通風。
• 當安裝上後，切記不要阻擋到後面板的風扇以維持適當的通風。
1
拆卸原本安裝在汽車內的音響系統，以及其裝配架。
注意：請務必保留所有從您汽車拆卸的螺絲和零件做日後使用。
2
將 (從汽車拆卸的) 裝配架安上本機 (參閱下圖)。
3
執行必要的電路連接。
• 參閱第 3 至 6 頁。
4
使用在步驟
1
拆卸的螺絲安裝本機。
以下以豐田（Toyota）汽車安裝為例。請聯絡您的 JVC 汽車音響分銷商有關更多細節。
When installing the unit in a Nissan car
當安裝本機於日產汽車時
當安裝本機於日產汽車時
Install the unit at an angle of less than 30˚, taking it into account that the monitor would eject
when in use.
when in use.
將本機安裝在少於 30˚ 的角度，您必須考慮到屏幕可以在使用時退出。
Required space for installation and the monitor ejection
安裝和顯示器退出所需的空間
安裝和顯示器退出所需的空間
Unit: mm
單位：mm（毫米）
單位：mm（毫米）
Mounting bracket removed from the car
從汽車拆卸的裝配架
從汽車拆卸的裝配架
Screws removed from the car in step
1
在步驟
1
從汽車拆卸的螺絲
Supplied screws
配備螺絲
配備螺絲
Select the appropriate type fitting to your audio
system space.
system space.
選擇適合您的音響系統安裝空間的型號。
Mounting bracket removed from the car
從汽車拆卸的裝配架
從汽車拆卸的裝配架
Plate for use with a Nissan car
用於日產汽車的框
用於日產汽車的框
CT_Instal_KW-AVX726[UT]2.indb 2
CT_Instal_KW-AVX726[UT]2.indb 2
08/12/25 16:33:12
08/12/25 16:33:12