Tascam 2488neo ユーザーズマニュアル

18

No tracks have 
been armed. Arm 
at least one 
track. 
 
Press [EXIT].

Before an auto-punch operation, you must have 
at least one armed track.

Press NO/EXIT and press the REC key of at 
least one track on which you will be recording 
(once a track has been armed in auto-punch, 
the track arming status cannot be changed).

19

Non-linear 
audio detected. 
Check your 
system set-up 
 
Press [EXIT].

Digital audio input mode has been selected, 
but the 2488neo has detected the wrong data 
format for the incoming digital audio to be used.

Press NO/EXIT and check the digital audio 
source. The 2488neo expects a signal in S/
PDIF (IEC60958 Consumer use) format at 
44.1 kHz. It cannot accept compressed audio 
formats, etc.

20

Not enough free 
disk space. Use 
DELETE UNUSED 
to make space. 
 
Press [EXIT].

Copying a song has failed because there is not 
enough space on the selected or target partition.

Press NO/EXIT and use one of the SONG 
menu operations such as DELETE UNUSED or 
ERASE to free up some space on the partition 
where there is not enough space (these opera-
tions cannot be undone).

21

Not enough free 
memory. Use 
DELETE UNUSED 
to free memory. 
 
Press [EXIT].

Sometimes after repeated operations, the inter-
nal memory of the 2488neo becomes used, and 
recording, etc. is not possible.

Press NO/EXIT. Use the DELETE UNUSED 
menu item from the SONG menu. As well as 
deleting the unused song data, this action 
will also free up memory, so recording can 
continue. Remember that this operation 
cannot be undone.

22

Not enough room on 
CD for burn. Use 
another CD [YES] 
or cancel [NO].

Too much data has been selected to fit onto the 
CD that is currently loaded.

Press YES/ENTER to change the CD for 
another one, or NO/EXIT to cancel the current 
operation. Use a higher-capacity disc when 
burning a master track or exporting data, or 
one of the same capacity as the current disc 
when backing up.

23

Not enough room 
on hard disk for 
this operation. 
 
Press [EXIT].

No enough space on the hard disk to create the 
image file necessary to create a CD.

Press NO/EXIT and create space by deleting 
songs, etc., (SONG->ERASE) backing them up 
if necessary (this operation cannot be undone). 
You can free up space on a partition other than 
the current partition (use the DISK->SELECT 
function) in order to create space for the image.

24

Protected song. 
Unprotect with 
SONG PROTECT. 
 
Press [EXIT].

Recording, track editing, recording, titling, etc. 
cannot be carried out when the current song 
has been protected.

Press NO/EXIT, and use the PROTECT menu 
item from the SONG menu to remove the 
protection from the song before proceeding.

25

Repeat mode is 
selected. 
Cannot do this 
operation now. 
 
Press [EXIT].

Because repeat mode is selected, the following 
functions cannot take place: locate operation, 
track editing, undo/redo, auto punch, quick 
routing, all menu operations, and shutdown.

Press NO/EXIT and cancel the repeat mode 
(REPEAT key) before proceeding with the 
operation that produced this message.

26

SSA mode is 
selected. 
Cannot do this 
operation now. 
 
Press [EXIT].

Because SSA mode is selected, the following 
functions cannot take place: MTC slave opera-
tions, jog and trim functions, recording (includ-
ing auto-punch) and digital input.

Press NO/EXIT and cancel the SSA mode 
(PITCH/SSA key) before proceeding with the 
operation that produced this message.