Korg Triton Studio ユーザーズマニュアル

If you want to play back an audio CD without applying 
the TRITON STUDIO’s effects, set “Input” Analog set-
tings for Input1 to “Level” 127, “Pan” L000, “BUS 
Select” L/R

, “Send1, 2” 000, and set Input2 “Pan” to 

 and the remaining parameters to the same set-

tings as for Input1.

Use “BUS Select” (Global P0: 0–3a) to set Inputs 1/2 buses 
by selecting from L/R, IFX1–5, 1–4, 1/2, 3/4, and Off.
“Send1 (to MFX1)” and “Send2 (to MFX2)” become effective 
only when “BUS Select” (Global P0: 0–3a) is set to L/R or 
Off

. If IFX1–5 is selected, use “Send1” and “Send2” for the 

post-IFX signal (

☞“3. Mixer”).

This setting is ignored in Sampling mode. Refer to “2–3. 
Sampling Mode” for information on the Sampling 
mode settings.

Insert effect settings are made in P8: Insert Effect of 1 Pro-
gram, 1 Combination, 1 Song, and Song Play modes. For the 
external input sound from the various input jacks, you can 
use the TRITON STUDIO’s effects as a 6-in 6-out effect pro-
cessor, or use them in conjunction with the internal sounds.
For example, in Program mode or Combination mode, you 
can route the incoming signal from AUDIO INPUTs 1 and 2 
and the oscillator sound to “Insert Effect 093: Vocoder” in 
order to set up a vocoder effect in which the internal sound 
is controlled by the mic inputs (“093: Vocoder” 

In Disk mode, the effects will have the settings of the 
previously-selected mode.

Use “Pan (CC#8),” “BUS Select,” “Send1,” and “Send2” of 
the P8: “Insert FX” page for the post-IFX signal in all modes 
to set the pan/bus and the send level to the Master Effects 
MFX1 and MFX2.
If you have checked the “Chain” box to connect the Insert 
Effects in series, these parameters “Pan (CC#8),” “BUS 
Select,” “Send1” and “Send2” for the post-IFX (last Insert 
Effect in the chain) signal become effective.

The master effects cannot be used in Sampling mode. 
This means that here you can set only the “Pan” (CC#8) 
that follows the insert effects.

This parameter enables you to set the pan of the post-IFX 
signal.
If you are using the stereo-in/stereo-out Insert Effects 
(

☞“In/Out”), set this parameter to “C064” to enable the 

“Pan” settings for the oscillators (Program P4: 4–1b, 4–4), 
timbres (Combination P0: 0–2b, P1: 1–1b), tracks (Sequencer 
P0: 0–3a/4a, Song Play P0: 0–3a/4a), and audio inputs (Sam-
pling P0: 0–2a, Global P0: 0–3a).

If you are using mono-in/stereo–out or mono-in/mono–out 
Insert Effects (

☞“In/Out”), the “Pan” settings for the oscil-

lators, timbres, tracks and audio inputs are ignored, and 
they are set to Center. Use the “Pan (CC#8)” parameter (P8: 
“Insert FX” page) to set the pan. “L000” is hard left, and 
“R127” is hard right.

You can control these parameters via CC#8.

This parameter enables you to specify the destination bus 
for the post-IFX signals. “L/R” is a common setting to send 
signals to the Master EQ before they are routed to the OUT-
PUT (MAIN) L/MONO and R outputs.
Select 1, 2, 3, 4, 1/2, or 3/4 to route the signals to OUTPUT 
(INDIVIDUAL) 1, 2, 3, or 4 (

☞“Individual Outputs”). Select 

“Off” so that no signals will be output to L/R, 1, 2, 3, or 4. In 
this case, the signals are routed from the Master Effects to 
AUDIO OUTPUT (MAIN). This setting is used when you 
are connecting the Insert Effects with the Master Effects in 
series using “Send1 (MFX1)” and “Send2 (MFX2).”

These parameters enable you to set the send level of the sig-
nals routed to Master Effects MFX1 and MFX2. These set-
tings are effective only when “BUS Select” is set to L/R or 
Off

.

If you are not using any Insert Effects, use “Send1” and 
“Send2” of the P8: “Routing” page in Program, Combina-
tion, Sequencer, and Song play modes to set the Master 
Effect send level (Use the Global P0: Input/Sampling page 
to set the send level for the audio inputs.).

“Send1” responds to CC#93 and “Send2” responds to 
CC#91.