Korg Triton Studio ユーザーズマニュアル

Using the Dynamic Modulation (Dmod) function enables 
you to control all effect parameters in real-time during per-
formance from the controllers of the TRITON STUDIO or a 
connected MIDI sequencer. You can also control the Pan 
(CC#8)

,” “Send1,” and “Send2” parameters in the same 

way.

You can control the parameters on MIDI Global channel 
(MIDI Channel” (Global P1: 1–1a).

Use “Ctrl Ch” parameters of the “IFX1–5” pages to set up 
the control channels for IFX1, 2, 3, 4, and 5. Select an appro-
priate option from Ch01–16, Gch, and All Routed.
Ch01–16:

 Select this when you want to control each insert 

effect from a different channel. An “*” symbol will be dis-
played at the right of the MIDI channel Ch01–16 of the tim-
bre that is routed to each insert effect. If the routed timbres 
have different MIDI channel settings, this parameter is used 
to specify the channel that will control the insert effect.
Gch:

 Select this option if you wish to control the parameters 

on MIDI Global channel “MIDI Channel” (Global P1: 1–1a). 
This is a common setting.
All Routed:

 Select this option to control the parameters on 

all the channels (channels 1–16 that have a “*” mark) that are 
routed to the corresponding Insert Effects.

Use “Ctrl Ch” parameters of the “IFX1–5” pages to set up 
the control channels for IFX1, 2, 3, 4, and 5. Select an appro-
priate option from Ch01–16 and All Routed.
Ch01–16:

 Select this when you want to control each insert 

effect from a different channel. An “*” symbol will be dis-
played at the right of the MIDI channel Ch01–16 of the track 
that is routed to each insert effect. If two or more tracks with 
differing MIDI channels Ch01–16 are being sent to a single 
insert effect, this parameter is used to specify the one track 
that will control the insert effect.
All Routed: 

Select this option to control the parameters on 

all the channels (channels 1–16 that have a “*” mark) that are 
routed to the corresponding Insert Effects.
“All Routed” is a typical option. If you wish to control the 
parameters on a single channel, you may select it from 
Ch01–16

.

The I/Os of Master Effects MFX1 and MFX2 are mono-in/
stereo-out

. “Send1” and “Send2” determine the send level 

to the Master Effects (

☞“Routing” and “Mixer”). Stereo sig-

nals will be combined to a mono signal automatically and 
sent to the effects.
The Master Effects do not output any Dry signals (signals 
that are not processed by the effects). Therefore, they output 
only Wet (signals that are processed by the effects) signals 
(set via the “Wet/Dry” of the “MFX1” and “MFX2” pages). 
The output signals from the Master Effects are routed to the 
L/R bus with the output level specified by “Return1” and 
“Return2.” These output signals are mixed with the output 
signals from the bus specified by “BUS Select” (P8: “Rout-
ing” page in each mode) L/R, or with the output signals 
from the bus specified by “BUS Select” (“Insert FX” page in 
each mode) L/R, then routed to the Master EQ.

Selecting “000: No Effect” will mute the output. The pro-
cessed signal will be output in one of the following ways, 
according to the type of effects 001–089.

The possible routing of effect signal inputs and outputs is 
indicated in the upper left corner of the block diagram.

Pressing the ON/OFF button for MFX1 and 2 of the P9: Mas-
ter FX page in each mode will toggle between ON and OFF. 
When OFF is selected, the output signals will be muted.

The TRITON STUDIO can also turn MFX 1 and 2 off 
separately from the setting of the ON/OFF button by 
receiving MIDI control change message CC#94 and 
CC#95 respectively. Value 0 will turn them off, and 
value 1–127 will turn them on. You can also use “Effect 
Global SW” (Global P0: 0–1b) to turn MFX1 and 2 on 
and off. This MIDI control is performed on MIDI Global 
Channel “MIDI Channel” (Global P1: 1–1a).

You cannot select double-size effects for Master Effects 
MFX1

 and MFX2.

+

+

+