Korg Triton Studio ユーザーズマニュアル

This stereo delay uses an LFO to sweep the delay time. The 
pitch also varies. You will obtain a delay sound with swell 
and shimmering. You can also control the delay time using a 
modulation source.

When the modulation source is used for control, this parameter 
reverses the left and right modulation direction.

The LFO can be reset via a modulation source.
The “Src” parameter sets the modulation source that resets the 
LFO. For example, you can assign Gate as a modulation source so 
that the sweep always starts from the specified point.
“L LFO Phase” and “R LFO Phase” set the phase obtained when 
the left and right LFOs are reset. In this way, you can create 
changes in pitch sweep for the left and right channels individu-
ally.

The effect is off when a value of the modulation source spec-
ified in the “Src” parameter is 63 or smaller, and the effect is 
on when the value is 64 or higher. The LFO is triggered and 
reset to the “L LFO Phase” and “R LFO Phase” settings 
when the value changes from 63 or smaller to 64 or higher.

This stereo delay controls the level of delay according to the 
input signal level. You can use this as a ducking delay that 
applies delay to the sound only when you play keys at a high 
velocity or only when the volume level is low.

a

Modulation Mode

LFO, D-mod

Switches between LFO modulation control and modulation source 
control

b

D-mod Modulation
Reversed L/R control by modulation source

L/R:+/+, L/R:+/–

 

☞

,

Src

Off...Tempo

Selects the modulation source that controls delay time

Response

0...30

Sets the rate of response to the modulation source

c

LFO Waveform
Selects LFO Waveform

Triangle, Sine

LFO Shape

–100...+100

Determines how much the LFO waveform is changed

☞

 Fx:020

d

LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

e

LFO Sync
Switches LFO reset off/on

Off, On

☞

,

Src

Off...Tempo

Selects the modulation source that resets the LFO

f

L LFO Phase [degree]

–180...+180

Sets the phase obtained when the left LFO is reset

☞

R LFO Phase [degree]

–180...+180

Sets the phase obtained when the right LFO is reset

☞

g

L Depth
Sets the depth of the left LFO modulation

0...200

R Depth
Sets the depth of the right LFO modulation

0...200

h

L Delay Time [msec]
Sets the left delay time

0.0...500.0

R Delay Time [msec]
Sets the right delay time

0.0...500.0

i

L Feedback
Sets the feedback amount of left delay

–100...+100

R Feedback
Sets the feedback amount of right delay

–100...+100

j

Wet/Dry

–Wet...–1:99, Dry, 1:99...Wet

☞

 Fx:010,

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100

a

Control Target
Selects from no control, output, and feedback

None, Out, FB

☞

Polarity
Reverses level control

+, –

☞

b

Threshold
Sets the level to which the effect is applied

0...100

☞

Offset
Sets the offset of level control

0...100

☞

c

Attack
Sets the attack time of level control

1...100

☞

d

Release
Sets the release time of level control

1...100

☞

e

L Delay Time [msec]
Sets the delay time for the left channel

0.0...680.0msec

f

R Delay Time [msec]
Sets the delay time for the right channel

0.0...680.0msec

g

Feedback
Sets the feedback amount

–100...+100

h

High Damp [%]
Sets the damping amount in the high range

0...100%

☞

 Fx:043

Low Damp [%]
Sets the damping amount in the low range

0...100%

☞

 Fx:043

i

Spread

–100...+100

Sets the width of the stereo image of the effect sound

☞

 Fx:043

j

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Sets the modulation amount of the effect balance

–100...+100

+