Korg Triton Studio ユーザーズマニュアル

• Before installing an option, be sure to disconnect the 

power supply cable and the connecting cables to any 
peripheral devices. Failure to do so could cause electrical 
shock or may damage the device.

• When installing, repairing, or replacing an option, you 

must perform only those actions that the owner’s 
manual directs, and no other.

• Do not apply excessive force to the electronic 

components or connectors on the circuit board(s) of an 
option, or attempt to disassemble them.
This could cause electric shock, fire, or malfunction.

• Before touching the option, touch a metal component of 

the device into which it will be installed, to discharge 
any static electricity that may be present in your body.
Static electricity may damage the electronic components.

• Be careful of any sharp edges or pointed metal parts on 

the option or the device into which the option is being 
installed.
Sharp edges or points may cause injury.

• Danger of explosion if battery is incorrectly replaced.

Replace only the same or equivalent type.

• When handling an option, never touch parts that are not 

related to the installation.
Doing so may cause electrocution or malfunctions.

• When handling an option, be careful not to touch the 

leads on the back side of the circuit board (the side 
opposite that on which the components are mounted).
The sharp points may cause injury.

• Do not allow the option or other device being installed 

to become wet, and do not allow objects to be placed on 
top of it.
Doing so could cause malfunction.

• When installing an option, be careful that screws or 

other parts do not fall into the device into which it is 
being installed.
Doing so could cause malfunction.

• So that static electricity in your body does not damage 

the electronic components, touch the ground wire of a 
grounded device or an unpainted metallic component 
to discharge any static electricity in your body before 
installing an option board or memory. Internal compo-
nents of the TRITON STUDIO and of the option/
memory boards may be damaged by static electricity.

• Follow the installation procedure, and be sure that 

each part is installed correctly and in the correct orien-
tation.

• Please use care in handling option boards/memory. 

Dropping them or applying pressure to them may 
damage the components.

• Avoid touching exposed metal edges of the circuit 

board, or portions that need not be handled during 
installation.

• Be careful not to lose the screws (and washers) that 

you remove.

• Do not use screws other than those that are installed in 

the option board/memory and the TRITON STUDIO. 
Using screws of a different shape or length may dam-
age the unit or cause it to malfunction.

• Be sure to firmly tighten the screws used for attach-

ment.

• Be sure that the option board/memory is inserted cor-

rectly into the connector or slot. After installation, be 
sure to check that the board is installed correctly. If the 
board is not inserted all the way, faulty contact or 
power supply shorts can occur, making the unit mal-
function.

• Be careful not to drop parts or the option board/mem-

ory into the inside of the instrument.
If you are unable to retrieve a screw or part that was 
dropped inside the instrument, please contact your 
local Korg distributor.

• So that static electricity in your body does not damage 

the electronic components, touch the ground wire of a 
grounded device or an unpainted metallic component 
to discharge any static electricity in your body before 
installing an option board or memory. Internal compo-
nents of the TRITON STUDIO and of the option/
memory boards may be damaged by static electricity.

• Follow the installation instructions, being careful not 

to reverse the polarity of the battery.

• Avoid touching exposed metal edges of the circuit 

board, or portions that need not be handled during 
installation.

• All screws (and washers) that are removed will be 

used, so be careful not to misplace them.

• Do not use screws other than those that are installed in 

the TRITON STUDIO. Using screws of a different 
shape or length may damage the unit or cause it to 
malfunction.

• Be sure to firmly tighten the screws used for attach-

ment.

• When installing the battery, do not use excessive force. 

Pressing the battery too hard or using excessive force 
may cause malfunctions or damage.

• Make sure that the battery is completely inserted into 

the battery holder. After installation, check to make 
sure that the battery is firmly in place.

Korg Inc. takes no responsibility for any malfunctions or 
damage that may occur from improper use or modifica-
tion of this product. Nor will Korg Inc. be responsible for 
any damages resulting from the loss or destruction of 
data.