Korg Electric Keyboard ユーザーズマニュアル

Adjusts the playback pitch of the sample in one-cent steps.

: The sample will sound at the original pitch when the orig-

inal key is played.
–:

 The pitch will be lowered. At a setting of –12.00 the pitch 

will be one octave lower.
+:

 The pitch will be raised. At a setting of +12.00 the pitch 

will be one octave higher.
You can also use “Pitch” to make fine adjustments in the 
length of a rhythm loop. For example with a setting of 
+12.00

, the playback speed will be doubled, and the loop 

playback time will be 1/2.
(☞PROG 2.1–2e Sample Parameter: Pitch)

The “Pitch BPM Adj.” lets you set the playback time in 
terms of a BPM value (☞4.1–2b).

  All notes in the zone of the index will sound 

at the pitch of the original key. Use this setting when you 
have sampled a drum sound or a rhythm loop, and want it 
to always playback at the original pitch.
Off (unchecked):

 The pitch will change in semitone steps, 

based on the original key. Use this setting when you have 
sampled a musical instrument sound etc. and would like to 
play it conventionally from the keyboard.

■

☞ “Delete SMPL,” “Copy SMPL,” “Move SMPL,” “Rename 

SMPL,” “SMPL To Stereo,” “Delete MS,” “Copy MS,” 
“Move MS,” “Rename MS,” “MS To Stereo/MS To 
Mono,” “Conv. To Prog,” “Keyboard Disp.” (1.1–3f)

This command sets the “Pitch” (4.1–2a) of the selected index 
on the basis of a BPM value. Raising the pitch of sample 
playback will increase the playback speed. Lowering the 
pitch will slow down the playback speed. This can be used 
to match the loop length etc. of the sample to a tempo of the 
desired BPM value.

1

Use “SMPL” (4.1–1b) to select the sample that you wish 
to edit.

2

From the Edit2 page “UTILITY,” choose “Pitch BPM 
Adj.” to open the following dialog box.

3

Specify “Beat.” This is specified in quarter-note beats.

4

“Current BPM” will show the BPM value at the base key 
(displayed in gray). This BPM value is calculated auto-
matically from the start address to the end address of the 
sample (if looping is off) or from the loop start address to 
the end address (if looping is on). 
For example if the start and end address of the sample 
are two seconds apart, the original key is specified as the 
base key, and “Beat” is set to 4, “Current BPM” would be 

. If “Beat” is set to 2, the display would indicate “Cur-

rent BPM” as 60.

It is not possible for this display to exceed the range of 
40–480

.

5

In “New BPM,” specify the BPM value that will result 
from the conversion of the “Current BPM” value.

6

To execute the Pitch BPM Adjust command, press the 
[F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.
When you execute this command, the “Pitch” (4.1–2a) 
value will be set automatically. For example if you mod-
ify a quarter-note 120 BPM sample to 240 BPM, the 
“Pitch” will be set to +12.00.

This calculation is performed within the TRITON Le’s 
limits of precision. Minor discrepancies may occur in 
the final BPM caclulation.

Here you can specify the default settings for indices that are 
created using “CREATE” (4.1–1c, 1.1–1c). New indexes will 
be created according the settings you specify here. You are 
free to modify the settings of an index later. Also, when you 
execute “INSERT” (4.1–1c), the “Position” setting specified 
here will be used (☞1.1–3b).

(☞ 1.1–3b: However, the parameter name and value name 
are shown differently.)

■

☞ “Delete SMPL,” “Copy SMPL,” “Move SMPL,” “Rename 

SMPL,” “SMPL To Stereo,” “Delete MS,” “Copy MS,” 
“Move MS,” “Rename MS,” “MS To Stereo/MS To 
Mono,” “Conv. To Prog,” “Keyboard Disp.” (1.1–3f), 
“Pitch BPM Adj.” (4.1–2b)

4.1–3a

4.1–3b