Korg Electric Keyboard ユーザーズマニュアル

 

When 

 

 is selected for this parameter, the left and right 

channels are linked to control the Limiter using the mixed signal. 
If

 

 (or 

 

) is selected, the left and right channels are 

linked, and the Limiter is controlled via only the left (or right) 
channel.
With 

 

, the left and right channels control the Lim-

iter individually.

 

This parameter sets the signal compression “Ratio”. Compression 
is applied only when the signal level exceeds the “Threshold” 
value.
Adjust the output level using the “G.Adj” parameter, since com-
pression causes the entire level to be reduced.

 

These parameters set the attack time and release time. A higher 
attack time will cause the compression to be applied more slowly.

 

These parameters are used to set the EQ applied to the trigger sig-
nal.
The Limiter determines whether the compression is applied or 
not, based on the post-EQ trigger signal. Setting the equalizer 
allows you to set the Limiter to respond to any frequency band.

 

Setting this parameter 

 

 will cause the trigger signal to be out-

put, instead of the effect sound. Use this parameter to check the 
trigger signal with EQ applied.
Usually, set this to 

 

.

 

This effect applies the Limiter to the low range, mid range, 
and high range of the input signal. You can control dynamics 
for each range to adjust the sound pressure of the low range, 
mid range, and high range in a different way from the EQ.

 

a

Envelope (Envelope Select) L/R Mix, L Only, R Only, L/R Individually
Selects from linking both channels, controlling only from left channel, 
only from the right channel, or controlling each channel individually

 

☞

 

b

Ratio

1.0:1...50.0:1, Inf:1

Sets the signal compression ratio

☞

c

Threshold

–40...0dB

Sets the level above which the compressor is applied

☞

d

Attack
Sets the attack time

1...100

☞

e

Release
Sets the release time

1...100

☞

f

Side PEQ Insert
Toggles between on/off of the trigger signal’s EQ

Off, On

☞

g

Trigger Monitor

Off, On

Switches between effect output monitor and trigger signal monitor

☞

h

EQ (Side PEQ Cutoff)

20...12.00kHz

Sets the EQ center frequency for the trigger signal

☞

Q
Sets the EQ bandwidth for the trigger signal

0.5...10.0

G (Gain)
Sets the EQ gain for the trigger signal

–18.0...+18.0dB

i

G.Adj (Gain Adjust)
Sets the output gain

–Inf, –38...+24dB

☞

,

(Source)
Selects the modulation source for the output gain

Off...Tempo

(Amount)
Sets the modulation amount of the output gain

–63...+63

j

W/D (Wet/Dly)

Dry, 1:99...99:1, Wet

(Source)

Off...Tempo

(Amount)
Sets the modulation amount of the effect balance

–100...+100

a

Ratio

1.0:1...50.0:1, Inf:1

Sets the signal compression ratio

☞

 Fx:03

b

Threshold

–40...0dB

Sets the level above which the compressor is applied

☞

 Fx:03

c

Attack
Sets the attack time

1...100

☞

 Fx:03

d

Release
Sets the release time

1...100

☞

 Fx:03

e

Low Offset
Gain of the low-range trigger signal

–40...0dB

☞

f

Mid Offset
Gain of the mid-range trigger signal

–40...0dB

☞

g

High Offset
Gain of the high-range trigger signal

–40...0dB

☞

h

G.Adj (Gain Adjust)

–Inf, –38...+24dB

Sets the output gain

☞

 Fx:03,

(Source)
Selects the modulation source for the output gain

Off...Tempo

(Amount)
Sets the modulation amount of the output gain

–63...+63

+