Korg Electric Keyboard ユーザーズマニュアル
COMBI
1.1
2.1
2.2
3.1
3.2
3.3
3.4
4.1
4.2
4.3
4.4
6.1
7.1
7.2
47
7.1–2c: Routing Map, BUS Select
This displays the bus to which the programs used by tim-
bres 1–8 will be sent.
bres 1–8 will be sent.
Routing Map
This displays the insert effect settings. The routing, the spec-
ified effect name, and the on/off status are shown.
ified effect name, and the on/off status are shown.
T01...8: BUS Sel
[DKit, L/R, IFX, 1, 2, 1/2, Off]
While viewing the map, you can specify the bus where each
timbre 1–8 will be sent.
Use the cursor keys to select the timbre, and use the [INC]/
[DEC] keys or the [VALUE] dial to set “BUS Select” (7.1–1a).
These settings can also be made in “BUS Select” (7.1–1a).
timbre 1–8 will be sent.
Use the cursor keys to select the timbre, and use the [INC]/
[DEC] keys or the [VALUE] dial to set “BUS Select” (7.1–1a).
These settings can also be made in “BUS Select” (7.1–1a).
■
7.1–2d: UTILITY
“Copy Insert Effect” (PROG 7.1–1c, 7.1–1b), “Dkit IFX
Patch” (7.1–1b), “Select by Category” (PROG 7.1–2c)
Patch” (7.1–1b), “Select by Category” (PROG 7.1–2c)
7.1–3: IFX
(Insert Effect)
Here you can adjust the parameters for the IFX that was
selected in the Setup page (☞p.164–).
selected in the Setup page (☞p.164–).
■
7.1–3a: UTILITY
☞ “Write Combination” (1.1–1c)
☞ For details on master effects, refer to p.155 “7. Effect
7.2–1: Setup
Here you can select the type of each master effect, turn it
on/off, and make chain and master EQ settings.
With the exception of “MFX1 Control Ch,” “MFX2 Control
Ch,” and “MEQ Control Ch,” this is the same as in Program
mode. (☞PROG 7.2: Ed-MasterFX)
on/off, and make chain and master EQ settings.
With the exception of “MFX1 Control Ch,” “MFX2 Control
Ch,” and “MEQ Control Ch,” this is the same as in Program
mode. (☞PROG 7.2: Ed-MasterFX)
7.2–1a: MasterFX Setup
MFX1 On/Off, MFX2 On/Off
[Off, ON]
Master Effect 1, 2
[00...89: name]
Rtn 1, 2 (Return 1, 2)
[000...127]
These are the same as in Program mode. Refer to “PROG
7.2–1: Setup.” However, the master effects will be controlled
on the “MFX 1, 2 Control Ch” MIDI channel, unlike in Pro-
gram mode.
The control changes used are the same as in Program mode.
7.2–1: Setup.” However, the master effects will be controlled
on the “MFX 1, 2 Control Ch” MIDI channel, unlike in Pro-
gram mode.
The control changes used are the same as in Program mode.
MFX 1, 2 Control Ch
[Ch01...16, G ch]
Selects the MIDI channel that will control dynamic
modulation (Dmod) for the master effects.
modulation (Dmod) for the master effects.
G ch
: The global MIDI channel “MIDI Channel” (GLOBAL
2.1–1a) will be used for control. Normally you will set this
parameter to G ch.
parameter to G ch.
7.2–1b: MasterFX Chain
MFX Chain
[Off, On]
Direction (Chain Direction)
[MFX1
→
MFX2, MFX2
→
MFX1]
Signal (Chain Signal)
[LR Mix, L Only, R Only]
Level (Chain Level)
[000...127]
These are the same as in Program mode. (☞PROG 7.2–1:
Setup)
Setup)
7.2–1c: MEQ Ctrl
MEQ Ctrl (MEQ Control Ch)
[Ch01...16, G ch]
Selects the MIDI channel that will control dynamic
modulation (Dmod) for the master EQ.
modulation (Dmod) for the master EQ.
G ch
: The global MIDI channel “MIDI Channel” (GLOBAL
2.1–1a) will be used for control. Normally you will set this
parameter to G ch.
parameter to G ch.
7.1–3a
COMBI 7.2: Ed–MasterFX
7.2–1a
7.2–1b
7.2–1c
7.2–1e
7.2–1d