Korg Electric Keyboard ユーザーズマニュアル

These settings specify the note and velocity ranges that will 
operate arpeggiators A and B.

This shows the “Scan Zone” for each arpeggiator, A and B.

Specifies the range of notes (keys) that will operate arpeg-
giator A. “Top” specifies the upper limit, and “Btm” speci-
fies the lower limit.

Specifies the range of velocities that will operate arpeggiator 
A. “Top” specifies the upper limit, and “Btm” specifies the 
lower limit.

Specify the range of notes (keys) and velocities that will 
operate arpeggiator B (☞“A: Key,” “A: Vel”).

The values of these parameters can also be entered by 
playing a note on the keyboard while you hold down 
the [ENTER] key.

■

☞ “Write Combination,” “Solo Selected Timbre” (1.1–1c), 

“Copy Arpeggiator” (6.1–1c)

☞ For details on insertion effects, refer to p.155 “7. Effect 

Here you can specify the output bus for each timbre 1–8. 
You can also specify the send level to the master effects.

Specifies the output bus for the program oscillator of each 
timbre 1–8. The current setting status can be viewed in the 
7.1–2c: Routing Map.

This can be selected only if the program for which set-

tings are being made is a drum program “Mode (Oscillator 
Mode) Drums” (PROG 2.1–1a). With a setting of DKit, the 
“BUS Select” (GLOBAL 5.1–3a) setting made for each key of 
the drum kit will be used.
For example if you have made “BUS Select” settings for each 
key of a drum kit so that the Snare sounds are sent to IFX 
and the other sounds are sent to L/R, selecting Dkit will 
send the Snare sounds to IFX and the other sounds to L/R. If 
you want to re-specify these routings, use Utility “DKit IFX 
Patch” (7.1–1b).

If this is set to 1/2, the programs of timbres 1–8 will be 
sent in stereo from AUDIO OUTPUT (INDIVIDUAL) 
1/2. If the pan of the program oscillator is controlled by 
MIDI control change #10 (pan) or AMS (Alternate Mod-
ulation Source), the sound will be output with the pan 
setting that is in effect at the moment of note-on. Unlike 
the case when this parameter is set to L/R, the pan of a 
sounding note will not change in real-time.
If you wish to move the pan of a sounding note in real-
time and output it from AUDIO OUTPUT (INDIVID-
UAL) 1/2, you must set “BUS Select” to IFX, select 00: 
No Effect 

for “IFX” (7.1–2a), and then set “BUS Select” 

(7.1–2a) to 1/2.

For each timbre 1–8, these parameters set the send level to 
master effects 1 and 2. These settings are valid when “BUS 
Select” is set to L/R or Off. When IFX is selected, the send 
levels to master effects 1 and 2 are set by the “S1 
(Send1(MFX)), ” “S2 (Send2(MFX))” parameters of the Setup 
page (7.1–2a), after the sound has passed through IFX.
If “BUS Select” is set to 1, 2 or 1/2 these settings are ignored.

6.1–4a

6.1–4b

Key zone of arpeggiator A

Velocity zone of
arpeggiator A

Velocity zone of
arpeggiator B

Key zone of arpeggiator B

C–1–G9

7.1–1a

7.1–1b