Hitachi C 8FSHE ユーザーズマニュアル
-3-
Slide cutting
HITACHI
C 8FSE
C 8FSHE
C 8FB2
P1 and P2
P3
B
Height x Width
(H x W)
65 x 312
(2-9/16” x 12-1/4”)
75 x 262
(2-15/16” x 10-5/6”)
with aux. board
width 30 (1-3/16”)
(2-9/16” x 12-1/4”)
75 x 262
(2-15/16” x 10-5/6”)
with aux. board
width 30 (1-3/16”)
65 x 305
(2-9/16” x 12”)
75 x 265
(2-15/16” x 10-7/16”)
(2-9/16” x 12”)
75 x 265
(2-15/16” x 10-7/16”)
60 x 270
(2-3/8” x 10-3/8”)
70 x 300
(2-3/4” x 11-13/16”)
60 x 270
(2-3/8” x 10-3/8”)
Workpieces as wide as shown in Table 2 can be cut with the motor
head sliding. The lower limit position of the saw blade is factory-
adjusted so that workpieces up to 65 mm (2-9/16") high and 312 mm
(12-1/4") wide can be cut as shown in Fig. 6-a. When cutting a
workpiece of 75 mm (2-15/16") in height as indicated in [ ] in Table 2,
adjust the saw so that there is a clearance of 2 to 3 mm (3/32" to 1/8")
between the bottom surface of the head and the top surface of the
workpiece at the lower limit position of the saw blade as shown in Fig. 6-b. (See the Instruction Manual
"Lower limit position of saw blade when cutting a large workpiece.")
Please note that, when cutting in this position, it is necessary to use an auxiliary board of 30 mm (1-3/16")
wide so that the workpiece on the fence side can be cut fully in width.
head sliding. The lower limit position of the saw blade is factory-
adjusted so that workpieces up to 65 mm (2-9/16") high and 312 mm
(12-1/4") wide can be cut as shown in Fig. 6-a. When cutting a
workpiece of 75 mm (2-15/16") in height as indicated in [ ] in Table 2,
adjust the saw so that there is a clearance of 2 to 3 mm (3/32" to 1/8")
between the bottom surface of the head and the top surface of the
workpiece at the lower limit position of the saw blade as shown in Fig. 6-b. (See the Instruction Manual
"Lower limit position of saw blade when cutting a large workpiece.")
Please note that, when cutting in this position, it is necessary to use an auxiliary board of 30 mm (1-3/16")
wide so that the workpiece on the fence side can be cut fully in width.
Press cutting
HITACHI
C 8FSE
C 8FSHE
C 8FB2
P1 and P2
P3
B
Height x Width
(H x W)
65 x 65
(2-9/16” x 2-9/16”)
65 x 65
(2-9/16” x 2-9/16”)
60 x 60
(2-3/8” x 2-3/8”)
70 x 40
(2-3/4” x 1-9/16”)
60 x 68
(2-3/8” x 2-11/16”)
Press cutting with the head swiveling enables cutting square
workpieces as large as shown in Table 3 in a single sawing
operation. It is convenient for cutting narrow workpieces (Fig. 7).
workpieces as large as shown in Table 3 in a single sawing
operation. It is convenient for cutting narrow workpieces (Fig. 7).
Table 2
Unit: mm (inch)
Table 3
Unit: mm (inch)
Fig. 5
Fig. 7
Fig. 6-b
Fig. 6-a
Max.
cutting
dimension
cutting
dimension
Maker
Model
Model
Maker
Model
Model
Max.
cutting
dimension
cutting
dimension