Nokia CC100 ユーザーズマニュアル

 

Dump all configurations/settings. 

 

Reset all settings to factory default, except Password. 

-t 

<mac>

 

-r 

<mac>

 

On-line EP connection diagnosis. 
-t: downstream SNR diagnosis(from Master to EP)  
-r: upstream SNR diagnosis(from EP to Master) 

<mac>

: EP MAC 

<mac>

 to be diagnosed 

 

Show detail file information resides in flash ROM. Include 
‘Working Area’ and ‘Upload Area’, refer

filenames are,  
‘

bootcode

’: boot loader 

‘

sysfw4m

’: system firmware 

‘

G1C28H21M

’: Master HCNA driver 

‘

G0C28H20Ep

’: 3010 EP HCNA driver 

‘

G1C28H21Ep

’: 3110 EP HCNA driver 

‘

diagsw

’: 3010 diagnosis utility file 

‘

diagsw1

’: 3110 diagnosis utility file 

Accompanying with file id, file version, file date, and file size. 

[

-s

 <pri/sec> <ip>] 

Display or set up DNS server setting. 
-s 

pri <ip>

: set up Primary DNS server’s IP 

-s 

sec

 

<ip>

: set up Secondary DNS server’s IP 

 

Close the Telnet console. 

 

Close the Telnet console. 

[

-c 

<hostcnt>]

  

[

-n 

<note>]

 

[

-u 

<uprate index>]

  

<mac>

 

 related setting values. 

<hostcnt>

 setting value (0~255), default 

255

 

<note>

 setting value 

<uprate index>

: EP 

 setting value ( 0~1563, 

*64Kbps), default 

0

 for unlimited  

<mac>

: designated EP MAC to configure 

-m 

<mac> 

Reset remote Smart EP device 

-m 

<mac> 

[

-r

] 

Display remote Smart EP port statistics for port 
LAN1/LAN2/HCNA. 
-r: reset all port statistics counter to 0 

-m 

<mac> 

[

-t

]  

[

-u

]  

[

-r

]  

[

-d

]  

[

-p

 <lan1/lan2/hpna>  

[

-l

 <up/down>]  

[

-s

 <auto /10h /10f 

/100h /100f>]  

[

-f

 <on/off>]] 

Display or set up remote Smart EP built-in switch Ethernet 
properties 
-t: display EP switch settings 
-u: display EP switch/port status 
-r: reset EP switch 
-d: reset EP switch’s eeprom settings to factory default 
-p: configure EP port LAN1/LAN2/HCNA 
-l: link,  

<up/down>

: force current port to link up or down, i.e. 

enable/disable current port

 

-s: current port Ethernet mode setting,  

<auto>

: auto-negotiation mode

 

<10h/10f/100h/100f>

: 10/100Mbps, half/full-duplex mode 

-f: current port Ethernet flow-control setting, 

<on/off>

: turn on /off flow control 

-m 

<mac>

 

Refer 

 for the 

same functionality, but operate on remote Smart EP with 
designated  MAC address 

<mac>

 

 [

-s

 <set> 

[

-c

 <act/deact>] 

[

-a

 <ip> 

-m

 <mask>]

[

-t

  <allow/deny>] 

[

-w

 <allow/deny>] 

Display or set up the filter rule set, refer the section “

” for IP 

<ip> 

and Subnet Mask setup 

<mask>

. 

<set>

:

 

filter set index, total 16 set (0~15) 

<act/deact>

: activate or de-activate the rule set 

<allow/deny>

: allow or deny the protocol