Nokia CC100 ユーザーズマニュアル

[

-s

 <set> 

[

-c

 <act/deact>] 

[

-p

 <port>] 

[

-a

 <ip>] 

[

-m

 <community>] ] 

Display or set up SNMP trap server(s) configuration. 

<set>

:

 

trap server index, at most 5 servers (0~4) 

<act/deact>

: activate or de-activate trap server IP 

<ip>

  

<port>

: SNMP trap UDP port number (0~65535), default 

162

 

<ip>

: trap server IP address 

<community>

: trap server community name, default ‘

public

’ 

[

-l

 <on/off>] 

[

-u

 <on/off>] 

[

-s

 <on/off>] 

[

-d

 <on/off>] 

Enable or disable specified trap type, 

<on/off>

: turn on or turn off this trap type, default is 

on

 

-l: logon/logoff trap 
-u: upload/upgrade firmware/driver trap 
-s: EP on-line status changed trap 
-d: EP diagnosis trap 

 

 

[

-c

 <act/deact>] 

[

-r

 <refresh time>] 

[

-z

 <time zone>] 

[

-s

 <set> -a 

address

] 

Display or set up SNTP configuration for 

<act/deact>

: activate or de-activate SNTP service for system 

time 

<refresh time>

: query SNTP server period, default

 60 

minutes 

<time zone>

: ‘+

hh

:

mm

’ or ‘-

hh

:

mm

’ to GMT time, 

hh

 for hours 

and 

mm

 for minutes, default ‘

+00:00

’

 

<set>

: 2 registered SNTP server set(0~1)

 

address: SNTP server host name or IP address in current set 

[

-r

] 

Display port statistics for port  LAN1/LAN2/HCNA. 
-r: reset all port statistics counter to 0 

[

-p

 <lan1/lan2> 

[

-s

 <auto /10h /10f 

/100h /100f>] ] 

Display or set up Ethernet port LAN1/LAN2 properties 

<lan1/lan2>

: configure LAN1 or LAN2 port

 

<auto>

: auto-negotiation mode

 

<10h/10f/100h/100f>

: 10/100Mbps, half/full-duplex mode

 

[

-c

 <on/off>] 

[

-t 

<QueryInterval 

(4~510, even 
number)>]] 

Display or set up IGMP v2 snooping configuration 

<on/off>

: enable or disable built-in IGMP v2 snooping function, 

default is off 

<Query Interval>

: expiry timer to age learned Multicast MAC if 

no IGMP query frame received from the router, default

is

248 

seconds (range from 4 to 510 in even) 

 [

-q

 <queue>  

[

-w

 <weight>] 

[

-d

 <discard mode>]]

Display or set up the QoS configuration, include priority queue, 
service weight and discard ratio while congestion, refer 

 

for more. 

<queue>

: select queue index (0~3) to configure, as q0(lowest 

priority)/q1/q2/q3(highest priority)

 

<weight>

: assign the queue with service weight(1~15), default 

1 

for q0, 

2 

for q1, 

3 

for q2 and 

4 

for q3

 

<discard mode>

: choose the discard mode(0~3) for queue 

utilization, default 

0 

for 0%. 

1 for 25%, 2 for 50% and 3 for 75%. refer 

[

-p

 <lan1/lan2>  

[

-d

 <tx/rx>] 

[

-c

 <on/off>] 

[

-r

 <N (1~1563 

rate=N*64kbps)>] ]

Display or set up the LAN1/LAN2 maximum rate. refer 

<lan1/lan2>

: configure LAN1 or LAN2 port 

<tx/rx>

:

 direction, incoming(rx) or outgoing(tx) 

 

<on/off>

: enable or disable control on this direction 

<N>

: the setup max rate (multiply value by 64kbps). Range 

from 0 to 1563, bandwidth control is invalid if N >= 1563

 

[

-s

 <set>  

[

-c

 <act/deact>] 

[

-p

 <port>  

-q

 <queue>] ] 

Display or set up the QoS configuration for TCP/UDP traffic 
classification, to assign higher priority for total 8 different 
TCP/UDP protocols 

<set>

:

 

rule set index, at most 8 set (0~7) 

<act/deact>

: activate or de-activate this set 

<port>

: TCP/UDP port number (0~65535), 

<queue>

: select queue index (0~3) for this rule set, as 

q0(lowest priority)/q1/q2/q3(highest priority)

 

[

-m

 <mac>] 

Display or set up the static MAC entry, total 8 entries of MAC