Sanyo PLC-XW200K ユーザーズマニュアル

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to  Part  15  of  the  FCC  Rules. These  limits  are  designed  to  provide  reasonable  protection  against  harmful

interference  in  a  residential  installation. This  equipment  generates,  uses,  and  can  radiate  radio  frequency

energy,  and  if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference

to  radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

 – Reorient or relocate the receiving antenna.

 – Increase the separation between the equipment and receiver.

 – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 – Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If

such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number  : PLC-XW200, PLC-XW250

Trade Name

: Sanyo

Responsible party  : SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.  : (818)998-7322

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC  Power  Cord  used  in  the  United  States  and  Canada  is  listed  by  the  Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the

plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable

to insert the plug into the outlet, contact your electrician.

GROUND

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin

face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the

same rating, marked thus

. If the fuse cover is detachable, never use the plug with the cover omitted. If a

replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug

(i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted.
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET 
OUTLET .

The Wires in this mains lead are coloured in accordance with the following code:

 Green-and-yellow Earth

 Blue . . . . . . . . . . . Neutral

 Brown  . . . . . . . . . Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by

the letter E or by the safety earth symbol   or coloured green or green-and-yellow.

The  wire  which  is  coloured  blue  must  be  connected  to  the  terminal  which  is  marked  with  the  letter  N  or

coloured black.

The  wire  which  is  coloured  brown  must  be  connected  to  the  terminal  which  is  marked  with  the  letter  L  or

coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED .