Elektra Beckum TKHS 315 E/P ユーザーズマニュアル
19
ENGLISH
2.
Attach cable with cable tie (32) to
the motor carrier unit.
the motor carrier unit.
A
Caution!
Make sure the cable does not
Make sure the cable does not
run over sharp edges and is not bent.
Riving knife adjustment.
A
Danger!
For shipping the riving knife is
For shipping the riving knife is
is lowered beneath the table top's
surface. Prior to initial operation the
riving knife therefore needs to be
adjusted:
surface. Prior to initial operation the
riving knife therefore needs to be
adjusted:
−
in the distance to the saw blade;
−
in its lateral alignment.
Distance to the saw blade:
The distance between the saw blade's
peripheral edge and the riving knife shall
be between 3...8 mm.
The riving knife must project at least the
same distance over the saw table as the
saw blade.
The distance between the saw blade's
peripheral edge and the riving knife shall
be between 3...8 mm.
The riving knife must project at least the
same distance over the saw table as the
saw blade.
1.
If necessary, loosen the Keps nut
(33) on the riving knife one turn.
(33) on the riving knife one turn.
2.
Adjust distance of the riving knife to
the saw blade.
the saw blade.
3.
Tighten the Keps nut.
Lateral alignment:
riving knife and saw blade must be per-
fectly in line.
riving knife and saw blade must be per-
fectly in line.
•
Turning the four hexagon socket
head cap screws (34) on the motor
carrier unit below the saw table
clockwise
= riving knife is moved to the right.
head cap screws (34) on the motor
carrier unit below the saw table
clockwise
= riving knife is moved to the right.
•
Turning the four hexagon socket
head cap screws (34) on the motor
carrier unit below the saw table
counter-clockwise
= riving knife is moved to the left.
head cap screws (34) on the motor
carrier unit below the saw table
counter-clockwise
= riving knife is moved to the left.
4.
Fit table insert extrusion (35) flush
into the saw table.
into the saw table.
5.
Turn the countersunk screw (36)
counter-clockwise against the stop.
counter-clockwise against the stop.
Installing the dust collection gear
1.
2.
3.
4.
Attach the hose carrier (42), with the
larger opening pointing to the rear,
to the saw table. To do so, loosen
the screws of the right-hand rear leg
and tighten again with the hose car-
rier in position.
larger opening pointing to the rear,
to the saw table. To do so, loosen
the screws of the right-hand rear leg
and tighten again with the hose car-
rier in position.
5.
Hook the suction hose into the hose
carrier.
carrier.
6.
Connect the saw's dust extraction
port at the chip case to a suitable
dust collector (see "Dust collector" in
chapter "Operation").
port at the chip case to a suitable
dust collector (see "Dust collector" in
chapter "Operation").
Mitre fence assembly
1.
2.
Install a mounting bracket (45) using
a hexagon head screw (46) and ser-
rated lock washer (47) to both ends
of the guide bar.
a hexagon head screw (46) and ser-
rated lock washer (47) to both ends
of the guide bar.
3.
Attach guide bar with mounting
brackets to front and rear of the
table top:
brackets to front and rear of the
table top:
−
30
31
32
33
Item
Description
Qty.
Blade guard
1
Suction hose
1
Hose carrier
1
34
35
36
37
38
Item
Description
Qty.
Fence carrier, lower
1
Guide bar
1
Mounting bracket
2
Hexagon head screw
M8 x 16
M8 x 16
6
Serrated lock washer
8.4
8.4
2
Washer 8.4
7
Flange nut M8
4
Fence carrier, upper
1
Star-knob screw
M8 x 23
M8 x 23
1
Fence extrusion,
short
short
1
Knurled nut M6
2
39
40
42
41
43
44
45
46
47