Elektra Beckum TKHS 315 E/P ユーザーズマニュアル
20
ENGLISH
−
4.
Align guide bar exactly parallel with
the table top's edge.
the table top's edge.
5.
Tighten all screws of mounting
brackets and guide bar.
brackets and guide bar.
6.
Swing the lower fence carrier up.
7.
8.
−
the wide edge of the fence extru-
sion must face the workpiece
sion must face the workpiece
−
the plastic nose of the fence
extrusion must point towards the
saw blade.
extrusion must point towards the
saw blade.
3
Note:
When the mitre fence is not
When the mitre fence is not
required swing it down, out of the way.
Table extension installation
1.
2.
Screw a hexagon thin nut (56) onto
the guide bar.
the guide bar.
3.
Install the rear table extension, with
the guide bar fitted to the table top's
rear edge left side.
the guide bar fitted to the table top's
rear edge left side.
4.
Screw another hexagon thin nut (56)
onto the guide bar from inside, to
hold it to the table top.
onto the guide bar from inside, to
hold it to the table top.
5.
Put a hexagon head screw (57) from
the narrow side through the plastic
guide bar bracket (58) and slide
plastic guide bar bracket onto the
guide bar.
the narrow side through the plastic
guide bar bracket (58) and slide
plastic guide bar bracket onto the
guide bar.
6.
3
Note:
When folded up the surface of
When folded up the surface of
the extension table must not be higher
than the table top's surface. Otherwise a
workpiece can get stuck at the extension
table.
than the table top's surface. Otherwise a
workpiece can get stuck at the extension
table.
7.
Adjust the hexagon thin nuts (56) on
the guide bar until the guide bar is
exactly parallel with the edge of the
table top.
the guide bar until the guide bar is
exactly parallel with the edge of the
table top.
8.
Tighten the hexagon thin nuts
against each other.
against each other.
9.
Fasten supports (60) with one each
hex. socket head bearing screw
(61), washer (62) and hexagon nut
(63) to the extension table.
hex. socket head bearing screw
(61), washer (62) and hexagon nut
(63) to the extension table.
10. Insert the supports into the slots pro-
vided in the short stanchion at the
rear of the saw.
rear of the saw.
11. If required, secure each support with
12. Tighten all hexagon head screws
and flange nuts of the saw's stand.
Accessory holder installation
In a final assembly step, two hexagon
head screws are fitted as holders for the
push stick, push block handle and
assembly wrench to the right front leg:
head screws are fitted as holders for the
push stick, push block handle and
assembly wrench to the right front leg:
1.
2.
Fit one hexagon head screws in the
hole at the front of the leg and
secure it with another flange nut.
hole at the front of the leg and
secure it with another flange nut.
48
49
50
51
52
53
Item
Description
Qty.
Guide bar, long
1
Plate, table rear
extension
extension
1
Hexagon thin nut
M12
M12
2
Hexagon head screw
M6 x 50
M6 x 50
1
Plastic bracket
1
Flange nut M6
3
Support
2
Hex. socket head
bearing screw
M8 x 15
bearing screw
M8 x 15
2
Washer 8.4
2
Hexagon nut M8
2
Hexagon head screw
M6 x 16
M6 x 16
2
54
55
56
57
58
59
Item
Description
Qty.
Hexagon head screw
M6 x 50
M6 x 50
2
–
Flange nut M6
4
60
61
62
63
64