Electrolux EKM 90310 X ユーザーズマニュアル

7

The wires in the mains 

cable

 are coloured 

as follows

:

GREEN AND YELLOW........EARTH
BLUE....................................NEUTRAL
BROWN ...............................LIVE

If

 the cable 

becomes

 damaged 

or worn

, replace it, 

observing

 the

following instructions:
- open the box of the supply board as 

shown

 

in

 the 

diagram

 below;

- unscrew screw “A” 

that secures

 the cable;

- replace the cable with one of the same

 length

 and 

which corresponds

to

 the features described 

in

 the table; switch the appliance off, and

shut 

the gas tap;

- 

connect

 the ‘green-yellow” earth wire to the terminal “      “, leaving

it approximately

 10 mm longer 

than

 the live 

wire

;

- 

connect

 the “blue” neutral wire 

to the terminal marked “N”

;

- 

connect 

the live wire 

to the terminal marked “L”

.

Always isolate the cooker from the electricity supply, 

shut 

off the gas

supply temporarily and proceed as follows.
- change the injectors,
- adjust the minimum flow of the burners.

To change

 the 

cooktop

 injectors,

 proceed

 as follows: remove the

grids, remove burners and flame-spreaders (see fig.A), change the
injector (see fig.B) and replace it with another one suitable for the
new type of gas (see table D). Re-assemble everything in 

reverse

order

, 

ensuring you position

 the flame-spreader 

correctly

.

Check

 that the voltage is the same as that stated on the rating plate.

The rating plate

 is located 

on the back cover.

If an fixed appliance is not equipped with supply cable and plug, the
power supply must be fitted with a disconnect switch in which the
distance between contacts permits total disconnection in accordance
with overvoltage category III, as required by installation regulations.
We recommend that the cooker circuit is rated to 13 amps.
Cable type HO5 RRF  3 X 1.5 mm

2

Open the mains terminal block cover as shown, unscrew screw “A”
the cable clamp

,

 and 

loosen

 the screws in the mains terminal block

“L N E” which secure the three
wires of the mains cable. Fit the
cable and refit screw “A”

,

 the cable

clamp.
Allow sufficient cable length for the
cooker to be pulled out for cleaning,
but do not let it hang

 lower

 than

50mm (2”) 

from

 the floor. The cable

can be looped if necessary, but
make sure that it is not kinked or
trapped when the cooker is in
position.

Fig. 11

To adjust the minimum, 

proceed

 as follows: switch the burner on, and

turn the knob towards the minimum flow position    

Remove the knob

from the tap, introduce a 

small

 screwdriver in 

to

 the tap rod (fig. 11).

Attention: in taps with security valve, the minimum 

adjustment

 screw

“Z” is placed outside the 

tap

 rod (fig. 12).

Isolate the cooker from the electricity supply before attempting to
replace the oven lamp.

is of a special type 

designed to

 withstand high

temperatures. To replace it, 

proceed 

as follows: 

remove 

the protect

ive

glass (A) and replace the burn

t-out

 

bulb

 with one of the same type.

Re

-fit

 the protecti

ve

 glass.

If it 

becomes

 necessary to repair or replace 

internal

 components,

proceed 

as follows: remove the glass lid from its position 

by sliding

off upwards.
Remove the grids, 

the 

burners and flame-spreaders (see   fig. 13),

unscrew the visible screws “V” 

located 

on the 

cooktop

 (see fig. 14).

Dismantle the cooktop

 by unscrewing the 4 rear screws “A” (see fig.

15 ).

Loosen

 the 

adjustment 

screw in order to increase the flow or 

tighten

it to decrease the flow.
The proper adjustment is obtained when the flame is 

approximately

3 or 4 mm 

in length

.

For butane/propane gas, the

 adjustment 

screw must be 

fully

 screwed

down

.

Make sure that the flame does not go out 

when 

passing quickly from

the max. flow 

to the minimum flow      .

Assemble the knob again.

Fig. 12

Z

                TABELLA GENERALE INIETTORI

Kind of gas

  mbar  

Nozzle

    

Burners

        

Power

 KW           Consum

             N°                          max.     min.   max.       min.

                          115    

Rapide

           3,00     0,75   286 l/h     72 l/h   reg.

NATURAL     20        97    

Semi rapide

   1,75     0,48   167 l/h     46 l/h   reg.

G 20                          72    

Auxiliary

        1,00     0,33     95 l/h     31 l/h   reg.

                               128    

Triple crown

   3,30     1,30    315 l/h   124 l/h   reg.

BUTANE    28-30    85     

Rapide

           3,00      0,75  219 g/h    55 g/h   42

G 30                        65     

Semi rapide

   1,75      0,48  128 g/h    35 g/h   31

                            50     

Auxiliary

        1,00      0,33     73 g/h    24 g/h  27

PROPANE    37       93    

Triple crown

   3,30     1,30   241 g/h    95 g/h   60

         G 31