Liebherr FI1051 ユーザーズマニュアル

Danger of fire and damage!

u

Do  not  place  devices  that  give  off  heat,  e.g.  micro-

waves, toasters, etc. on the appliance.

Risk of personal injury!

u

Have two people move this appliance into place.

Risk of damage caused by condensation

Installing  the  appliance  next  to  any  other  refrigerator  or

freezer  can  cause  condensation  or  damage  to  the  Lieb-

herr appliance.

u

Do not install this appliance next to any other refriger-

ator or freezer except another Liebherr model. Liebherr

models are designed to allow side-by-side installation.

They are equipped with a heating system to eliminate

condensation  when  refrigerators  or  freezers  are

installed side-by-side.

Risk of damage for the finished floor surface!

u

Protect the finished floor surface before you uncrate the

unit.

Verify that:
q The floor under the appliance is flat and level.
q The  floor  can  support  the  appliance's  weight  plus

approximately 1200 pounds (544 kg) of food weight.

q The  appliance  is  not  placed  in  direct  sunlight  or  near

the  stove,  range  top,  radiators  and  similar  heat

sources.

q The kitchen cabinet that the appliance is installed in is

shimmed  to  the  floor  level  if  the  floor  heights  are  not

equal.

q Cutout dimensions are accurate.
q Electrical outlet is in correct location.
q The air flow is not restricted. Air flow must be provided

for  the  appliance  to  operate  properly.  The  factory  air

vents  provide  31  square  inches  (200  cm

2

)  of  air  flow

per appliance. If you are replacing the air vents with an

overlay, the air flow must be the same or greater than

the factory air vents.

u

Examine the unit and packaging for shipping damage.

Contact the carrier immediately if you suspect there is

any damage.

u

Note the type (model, number), index, appliance/serial

number,  date  of  purchase  and  where  purchased

u

Remove anything attached to the rear or side walls of

appliance  that  would  prevent  proper  installation  or

impede proper ventilation.

u

Remove  the  protective  film  from  the  outside  of  the

appliance.

u

Clean the appliance (see 6.3) .

If  the  appliance  is  set  up  in  humid  areas,  condensation

may build on the outside of the appliance.

u

Always ensure proper ventilation.

u

Assemble appliances according to separate installation

instructions.

Danger of suffocation from packaging materials and films!

u

Do not allow children to play with packaging materials.

The packaging is made from recyclable materials:
- Corrugated card/cardboard

- Parts made of foamed polystyrene

- Films and bags from polyethylene

- Packing bands from polypropylene

- Wood frame nailed together with a polyethylene

window*

u

Take  the  packaging  material  to  an  official  collection

point.

Electrical shock hazard!

u

Start-up should only take place once the appliance has

been installed according to these instructions.

u

Electrically ground appliance.

u

Do not ground to a gas pipe.

u

Check with a qualified electrician if you are not sure the

appliance is properly grounded.

u

Do not have a fuse in the neutral or grounding circuit.

u

Do not use an extension cord, power bar or a multiple

socket adapter.

u

Do not use a power cord that is frayed or damaged.

Electrical shock hazard!

This appliance is equipped with a three-prong (grounding)

polarized plug for your protection against possible shock

hazards. Electrical Grounding Required.

u

Do  not  remove  the  round  grounding  prong  from  the

plug.

u

Use only an grounded adapter.

- Wait  1  hour  after  installation  before  you  plug  in  the

appliance. This allows the refrigerant and system lubri-

cation to reach equilibrium.

- Make sure incoming voltage is the same as the appli-

ance rating. A 110-120 Volt, 60 Hz, 15 Amp electrical

supply  (20  Amp  for  side-by-side  installations)  circuit

that is controlled by a circuit breaker or fuse is required.